Subaru Crosstrek Service Manual: Dtc b1810 short in driver s airbag dual stage - 2nd step

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Airbag main harness circuit is shorted.

• Airbag module harness (driver’s side) circuit is shorted.

• Roll connector circuit is shorted.

• Driver’s airbag module is faulty.

• Airbag control module is faulty.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

Prior to starting work, prepare two AIRBAG RESISTORs (98299PA040).

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module and the driver’s airbag module.

Is there poor contact?

Replace the airbag harness.

Diagnostic Chart with Trouble Code > DTC B1810 SHORT IN DRIVER’S AIRBAG DUAL STAGE - 2ND STEP">Go to Step 2.

2.CHECK DRIVER’S AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Remove the driver’s airbag module.

3) Connect the connector (1N) in the test harness N to the connector (AB38).

4) Connect the airbag resistor to the connector (2N) of test harness N.

5) Connect the connector (1Q) in the test harness Q to connector (AB37).

6) Connect the airbag resistor to the connector (2Q) in the test harness Q.

7) Connect the battery ground terminal and turn the ignition switch to ON.

Does the airbag warning light illuminate for six seconds and go off?

Replace the driver’s airbag module. Driver’s Airbag Module">

Diagnostic Chart with Trouble Code > DTC B1810 SHORT IN DRIVER’S AIRBAG DUAL STAGE - 2ND STEP">Go to Step 3.

3.CHECK ROLL CONNECTOR AND AIRBAG MAIN HARNESS (DRIVER’S AIRBAG HARNESS).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Remove the console front panel and disconnect the connector (AB9).

3) Disconnect the connector (AB66) from the driver’s knee airbag module.

4) Disconnect the airbag resistor from the connector (2N) in test harness N and from the connector (2Q) in test harness Q.

5) Disconnect the connectors (AB6, AB17, AB18) from the airbag control module, and connect the connector (1AG) in the test harness AG.

6) Measure the resistance between connector (2N) terminals in test harness N.

Connector & terminal

(2N) No. 1 — (2N) No. 2:

Is the resistance 1 M? or more?

Diagnostic Chart with Trouble Code > DTC B1810 SHORT IN DRIVER’S AIRBAG DUAL STAGE - 2ND STEP">Go to Step 5.

Diagnostic Chart with Trouble Code > DTC B1810 SHORT IN DRIVER’S AIRBAG DUAL STAGE - 2ND STEP">Go to Step 4.

4.CHECK AIRBAG MAIN HARNESS (DRIVER’S AIRBAG HARNESS).

1) Remove the instrument panel lower cover and column cover, and disconnect the connector (AB7) from (AB2).

2) Disconnect the test harness Q from connector (AB37).

3) Measure the resistance between connector (3AG) terminals in test harness AG.

Connector & terminal

(3AG) No. 2 — (3AG) No. 4:

Is the resistance 1 M? or more?

Replace the roll connector. Roll Connector">

Replace the airbag main harness along with body harness.

5.CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.

2) Clear the memory. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B1810 displayed?

Replace the airbag control module. Airbag Control Module">

Diagnostic Chart with Trouble Code > DTC B1810 SHORT IN DRIVER’S AIRBAG DUAL STAGE - 2ND STEP">Go to Step 6.

6.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Dtc b1808 short in passenger s airbag (to +b)

Dtc b1811 open in driver s airbag dual stage - 2nd step

Other materials:

Welcome screen and Good-bye screen
When the driver's door is opened and closed after unlocking the door, the welcome screen will appear on the multi information display for approximately 20 seconds. When the ignition switch is turned to the "LOCK"/"OFF" position, the multi information display gradually turns off (Good-bye s ...

Hill start assist warning light does not go off
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Warning Light Illumination PatternHILL START ASSIST WARNING LIGHT DOES NOT GO OFFDetecting condition:• Defective combination meter• Defective CAN communicationTrouble symptom:Hill start assist warning light does not go off when starting t ...

Front seats
WARNING Never adjust the seat while driving to avoid loss of vehicle control and personal injury. Before adjusting the seat, make sure the hands and feet of rear seat passengers and cargo are clear of the adjusting mechanism. After adjusting the seat, push it slightly to make sur ...