Subaru Crosstrek Service Manual: Dtc u0424 invalid data received from hvac control module

DTC DETECTING CONDITION:

Defective data was transmitted from A/C control panel.

TROUBLE SYMPTOM:

Cooperation control of air conditioner does not operate properly.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0424 INVALID DATA RECEIVED FROM HVAC CONTROL MODULE">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0424 INVALID DATA RECEIVED FROM HVAC CONTROL MODULE">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is DTC for the bus off or the data no-receive displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0424 INVALID DATA RECEIVED FROM HVAC CONTROL MODULE">Go to Step 4.

4.CHECK DTC.

Check the displayed DTC.

Is U0424 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0424 INVALID DATA RECEIVED FROM HVAC CONTROL MODULE">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0424 INVALID DATA RECEIVED FROM HVAC CONTROL MODULE">Go to Step 9.

5.CHECK DTC.

1) Turn the ignition switch to OFF.

2) Disconnect the A/C control panel connector.

3) Connect the disconnected connectors.

4) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0424 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0424 INVALID DATA RECEIVED FROM HVAC CONTROL MODULE">Go to Step 6.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0424 INVALID DATA RECEIVED FROM HVAC CONTROL MODULE">Go to Step 9.

6.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the air conditioner data abnormal detected in several modules?

Replace the A/C control panel. Control Panel">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0424 INVALID DATA RECEIVED FROM HVAC CONTROL MODULE">Go to Step 7.

7.REPLACE MODULE.

1) Replace the A/C control panel.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0424 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0424 INVALID DATA RECEIVED FROM HVAC CONTROL MODULE">Go to Step 8.

System is normal.

8.CHECK MODULE.

1) Restore the A/C control panel.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0424 a current malfunction?

Replace the A/C control panel. Control Panel">

System is normal.

9.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0424 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0424 INVALID DATA RECEIVED FROM HVAC CONTROL MODULE">Go to Step 10.

10.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u0423 invalid data received from instrument panel cluster control module

Dtc u0427 invalid data received from vehicle security control module

Other materials:

Ornament Installation
EXTERIOR/INTERIOR TRIM > OrnamentINSTALLATION1. LETTER MARKAlign the end of application tape with the end of panel, then adhere the letter mark.(a)Panel - rear gate end(b)Application tape end NOTE:• Align the cutout of application tape with the end reference of the front door. (a)• A ...

Drive cycle Procedure
ENGINE (DIAGNOSTICS)(H4DO) > Drive CyclePROCEDUREIt is necessary to perform the drive cycle listed below if DTC is not found in the Inspection Mode. It is possible to complete diagnosis of the DTC by performing the indicated drive cycle. After the repair for the DTC, perform a necessary drive cyc ...

Entering the vehicle while it is running via remote start
1. Unlock the vehicle doors using the keyless access function (if equipped) or remote keyless entry system. If the vehicle's doors are unlocked manually using the key, the vehicle's alarm system will trigger (if the alarm system is armed prior to activating the remote engine start system) and ...