Subaru Crosstrek Service Manual: Dtc u0402 invalid data received from tcm

DTC detecting condition:

Received error data from TCM.

Trouble symptom:

Sport indicator light blinks.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0402 INVALID DATA RECEIVED FROM TCM">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0402 INVALID DATA RECEIVED FROM TCM">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is DTC for the bus off or the data no-receive displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0402 INVALID DATA RECEIVED FROM TCM">Go to Step 4.

4.CHECK DTC.

Check the displayed DTC.

Is U0402 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0402 INVALID DATA RECEIVED FROM TCM">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0402 INVALID DATA RECEIVED FROM TCM">Go to Step 9.

5.CHECK DTC.

1) Turn the ignition switch to OFF.

2) Disconnect the TCM connector.

3) Connect the disconnected connectors.

4) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0402 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0402 INVALID DATA RECEIVED FROM TCM">Go to Step 6.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0402 INVALID DATA RECEIVED FROM TCM">Go to Step 9.

6.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the transmission data abnormal detected in several modules?

Replace the TCM. Transmission Control Module (TCM)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0402 INVALID DATA RECEIVED FROM TCM">Go to Step 7.

7.REPLACE MODULE.

1) Replace the TCM.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0402 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0402 INVALID DATA RECEIVED FROM TCM">Go to Step 8.

System is normal.

8.CHECK MODULE.

1) Reinstall the TCM.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0402 a current malfunction?

Replace the TCM. Transmission Control Module (TCM)">

System is normal.

9.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Using the Subaru Select Monitor, read DTC of CAN system. Read Diagnostic Trouble Code (DTC)">

Is U0402 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0402 INVALID DATA RECEIVED FROM TCM">Go to Step 10.

10.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u0401 invalid data received from ecm/pcm a

Dtc u0416 invalid data received from vehicle dynamics control module

Other materials:

Dtc p0843 transmission fluid pressure sensor/switch "a" circuit high
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0843 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT HIGHDTC detecting condition:Immediately at fault recognitionTrouble symptom:Shift characteristics malfunctionCAUTION: ...

Inspection
LIGHTING SYSTEM > Spot Map LightINSPECTION1. SPOT MAP LIGHT BULB1. Visually check the bulb for blow out.2. Check the bulb specification. General Description > SPECIFICATION">3. Replace the bulb if it is found defective.2. SPOT MAP LIGHT SWITCH1. Check the resistance between switch ter ...

Inspection
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > Subaru Select MonitorINSPECTION1. COMMUNICATION FOR INITIALIZING IMPOSSIBLE (COMBINATION METER)Detecting condition:• Defective harness connector• Power supply circuit malfunction• Defective combination meter• Defective CAN commun ...