Subaru Crosstrek Service Manual: Dtc p2530 ignition switch run position circuit

Subaru Crosstrek Service Manual / Continuously variable transmission (diagnostics) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p2530 ignition switch run position circuit

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P2530 IGNITION SWITCH RUN POSITION CIRCUIT

DTC detecting condition:

Immediately at fault recognition

Trouble symptom:

Faulty TCM operation

CAUTION:

Use the check board when measuring the TCM terminal voltage and resistance.

Wiring diagram:

CVT control system CVT Control System">

STEP	CHECK	YES	NO

1.CHECK CONNECTOR.

Check the installing condition of TCM connector.

Is the TCM connector installed properly?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2530 IGNITION SWITCH RUN POSITION CIRCUIT">Go to Step 2.

Install the TCM connector.

2.CHECK INPUT VOLTAGE OF TCM.

1) Turn the ignition switch to OFF.

2) Disconnect the TCM connector.

3) Turn the ignition switch to ON.

4) Measure the voltage between TCM connector and chassis ground. (While wiggling the harness)

Connector & terminal

(B54) No. 41 (+) — Chassis ground (−):

Is the voltage 8 V or more?

Even if DTC is detected, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, the following items may be the cause of fault.

• Open circuit or short circuit to ground of harness between TCM connector and ignition switch connector (IG relay 1 connector for model with push button start)

• Poor contact of ignition switch connector (IG relay 1 connector for model with push button start)

• Poor contact of ignition switch (IG relay 1 for model with push button start)

Repair the harness and connector.

NOTE:

In this case, repair the following item:

• Open circuit or short circuit to ground of harness between TCM connector and ignition switch connector (IG relay 1 connector for model with push button start)

• Poor contact of ignition switch connector (IG relay 1 connector for model with push button start)

• Poor contact of ignition switch (IG relay 1 for model with push button start)

1. OUTLINE OF DIAGNOSIS

• Detect the malfunction of ignition SW circuit.

• Judge as NG if the ignition SW signals are lost 5 times or more even though the engine is ON.

2. EXECUTION CONDITION

Secondary parameters	Execution condition
12 V battery system voltage	≥ 10.9 V
Engine speed	≥ 400 rpm

3. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria	Threshold Value
Count of temporarily discontinuous input of ignition switch	≥ 5 count

Time Needed for Diagnosis: 5 seconds

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p062f internal control module eeprom error

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P062F INTERNAL CONTROL MODULE EEPROM ERRORDTC DETECTING CONDITION:Detected when two con ...

Dtc p0601 internal control module memory checksum error

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0601 INTERNAL CONTROL MODULE MEMORY CHECKSUM ERRORDTC DETECTING CONDITION:Detected whe ...

Other materials:

Dtc b1693 door sensor rh initialization incomplete
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B1693 DOOR SENSOR RH INITIALIZATION INCOMPLETEDiagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting condition:• Open or short circuit in harness of side sensor bus (RH)• Front door impact sensor (RH ...

Removal
MECHANICAL(H4DO) > CamshaftREMOVAL1. CAMSHAFT RHThe camshaft RH and cam carrier are designed as removing as a unit. Refer to “Cam Carrier” for removal procedures of camshaft RH. Cam Carrier > REMOVAL"> Cam Carrier > DISASSEMBLY">2. CAMSHAFT LHThe camshaft LH an ...

Voice command system operation
1. Press the talk switch on the steering wheel. After the voice command top screen has been displayed, speech guidance will commence. NOTE When the voice command mode is audio mode, voice guidance for the voice command system can be skipped by pressing the talk switch on the steering ...