Subaru Crosstrek Service Manual: Dtc p0019 crankshaft position - camshaft position correlation bank 2 sensor b

DTC detecting condition:

Detected when two consecutive driving cycles with fault occur.

Trouble symptom:

• Engine stall

• Improper idling

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

1.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is DTC other than P0016, P0017, P0018 or P0019 displayed?

Check the appropriate DTC using the “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0019 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR B">Go to Step 2.

2.CHECK EXHAUST OIL CONTROL SOLENOID LH.

Check the exhaust oil control solenoid LH. Oil Control Solenoid > INSPECTION">

Is the check result OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0019 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR B">Go to Step 3.

Replace the exhaust oil control solenoid LH. Oil Control Solenoid">

3.CHECK INSTALLATION CONDITION OF TIMING CHAIN.

Using ST and by turning the crankshaft, align the alignment marks of crank sprocket, intake cam sprocket and exhaust cam sprocket. Timing Chain Assembly">

Is the timing chain installed in the proper position?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0019 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR B">Go to Step 4.

Correct the installation condition of timing chain. Timing Chain Assembly">

4.CHECK CAM CARRIER FILTER.

Check the filter installed to the cam carrier. Cam Carrier > INSPECTION">

Is the check result OK?

Replace the exhaust cam sprocket LH. Cam Sprocket"> After the operation is complete, go to the next step. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0019 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR B">Go to Step 5.

Replace the cam carrier filter. Cam Carrier">

5.CHECK CURRENT DATA.

1) Clear the memory using the Subaru Select Monitor or general scan tool. Clear Memory Mode > OPERATION">

2) Start the engine and warm up completely.

3) Using the Subaru Select Monitor, read the values of «VVT Ex Initial Position Learning Value #2» and «Exh. VVT Retard Ang. L» while the vehicle is in stable condition for 30 seconds or more with the engine idling.

NOTE:

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

4) Calculate the values using the following formula. Ignore the unit at this time.

|«VVT Ex Initial Position Learning Value #2» − (90 − «Exh. VVT Retard Ang. L»)|

Is the calculation result less than 10?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0019 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR B">Go to Step 6.

Replace the ECM. Engine Control Module (ECM)">

6.CHECK DTC.

1) Clear the memory using the Subaru Select Monitor or general scan tool. Clear Memory Mode > OPERATION">

2) Perform drive cycle N. Drive Cycle > PROCEDURE">

Is the same DTC as current diagnosis output?

Replace the ECM. Engine Control Module (ECM)">

End.

For the detection standard, refer to DTC P0017. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0017 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 1 SENSOR B">

Dtc p0018 crankshaft position - camshaft position correlation bank 2 sensor a

Dtc p0020 "a" camshaft position actuator control circuit/open bank 2

Other materials:

Disassembly
STARTING/CHARGING SYSTEMS(H4DO) > GeneratorDISASSEMBLY1. Remove the cap from the generator.2. Remove four bolts.3. Use a drier to heat the rear cover (A) portion to 50 — 60°C (122 — 140°F).4. Insert a flat tip screwdriver or similar tool wrapped with protective tape into ...

Removal
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Blower Motor Unit AssemblyREMOVALCAUTION:Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">1. Disconnect the ground ...

Capacity
SPECIFICATIONS > CrosstrekCAPACITYModel2.0 L DOHC non-turbo5MTCVTFuel tankL (US gal, Imp gal)60 (15.9, 13.2)Engine oilTotal capacity (at overhaul)L (US qt, Imp qt)5.7 (6.0, 5.0)Filling amount of engine oilL (US qt, Imp qt)When replacing engine oil and oil filter4.8 (5.1, 4.2)When replacing engine ...