Subaru Crosstrek Service Manual: Dtc c2124 transmitter 4 no data

DTC DETECTING CONDITION:

Detected when no data is received from each transmitter for 8 minutes or more at a vehicle speed of 40 km/h (25 MPH) or more. (Timer is not cleared when the vehicle speed becomes lower than 40 km/h halfway.)

TROUBLE SYMPTOM:

Tire pressure warning light blinks 25 times and then illuminates.

1.REPRODUCTION OF FAILURE.

1) Perform the drive test.

Drive the vehicle at 40 km/h (25 MPH) or faster for at least 10 minutes.

2) Read the DTC of tire pressure monitoring. Read Diagnostic Trouble Code (DTC)">

Is DTC displayed as “Present fault”?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 2.

When DTC is displayed as “Past faults”, the system has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, there may be temporary poor communication due to radio wave environment inside/outside the vehicle.

2.START FRONT LEFT TRANSMITTER.

1) Connect the Subaru Select Monitor and then turn the ignition switch to ON.

2) Select «Data monitor» of the tire pressure monitor. Read Current Data">

3) Use the transmitter registration tool and transmit the ID from the front left transmitter to check «Latest reception ID».

Is «Latest reception ID» updated?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 3.

Replace the front left transmitter. Tire Pressure Monitoring System">

3.CHECK FRONT LEFT TRANSMITTER ID.

Compare the ID on the latest ID display with «Registered ID 1».

Are the two IDs same?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 4.

Record «Latest reception ID» as the front left. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 4.

4.START FRONT RIGHT TRANSMITTER.

Use the transmitter registration tool and transmit the ID from the front right transmitter to check «Latest reception ID».

Is «Latest reception ID» updated?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 5.

Replace the front right transmitter. Tire Pressure Monitoring System">

5.CHECK FRONT RIGHT TRANSMITTER ID.

Compare the ID on the latest ID display with «Registered ID 2».

Are the two IDs same?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 6.

Record «Latest reception ID» as the front right. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 6.

6.START REAR RIGHT TRANSMITTER.

Use the transmitter registration tool and transmit the ID from the rear right transmitter to check «Latest reception ID».

Is «Latest reception ID» updated?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 7.

Replace the rear right transmitter. Tire Pressure Monitoring System">

7.CHECK REAR RIGHT TRANSMITTER ID.

Compare the ID on the latest ID display with «Registered ID 3».

Are the two IDs same?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 8.

Record «Latest reception ID» as the rear right. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 8.

8.START REAR LEFT TRANSMITTER.

Use the transmitter registration tool and transmit the ID from the rear left transmitter to check «Latest reception ID».

Is «Latest reception ID» updated?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 9.

Replace the rear left transmitter. Tire Pressure Monitoring System">

9.CHECK REAR LEFT TRANSMITTER ID.

Compare the ID on the latest ID display with «Registered ID 4».

Are the two IDs same?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 10.

Record «Latest reception ID» as the rear left. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 10.

10.CHECK MALFUNCTION TRANSMITTER.

Is ID recorded by this procedure?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 11.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA">Go to Step 2.

11.CHECK MALFUNCTION TRANSMITTER.

Check the registered ID of the transmitter indicated by DTC.

Is there checked ID in the record?

Replace the transmitter of the recorded position. Tire Pressure Monitoring System">

Replace the transmitter showing the latest ID that is not included in the registered IDs. Tire Pressure Monitoring System">

When driving vehicle to perform driving test, there should be always 2 persons (driver and checker) to check.

Dtc c2123 transmitter 3 no data

Dtc c2221 transmitter 1 pressure data abnormal

Other materials:

Assembly
MECHANICAL(H4DO) > Cylinder BlockASSEMBLY1. CYLINDER BLOCK1. Apply liquid gasket to the threaded portion of the main gallery plug, and install the main gallery plug to the cylinder block LH.NOTE:Before applying liquid gasket, degrease the thread holes of the cylinder block LH and main gallery plu ...

Operation
TIRE PRESSURE MONITORING SYSTEM (DIAGNOSTICS) > Subaru Select MonitorOPERATIONFor detailed operation procedures, refer to “Application help”.NOTE:If TPMS & keyless entry CM or TPMS CM and Subaru Select Monitor cannot communicate, check the communication circuit. Subaru Select Mon ...

Defogger setting
1. Perform the preparation steps according to "Preparation for car settings" 2. Operate the " " or "  " switch to select the "Defogger" item. Then push the button. 3. The current setting will be displayed. Push the  button to enter the selection mode. 4. Select ...