Subaru Crosstrek Service Manual: Dtc c1732 lateral g sensor

DTC detecting condition:

Defective lateral G sensor

Trouble symptom:

• ABS does not operate.

• VDC does not operate.

• Hill start assist does not operate.

1.CHECK INSTALLATION OF VDCCM&H/U.

Is VDCCM&H/U installed properly without being tilted?
Is the bracket deformation-free?
Are the VDCCM&H/U installation bolts installed without missing or getting loose?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR">Go to Step 2.

Repair the defective part.

• Install VDCCM&H/U properly.

• Replace the bracket if faulty.

• Tighten the VDCCM&H/U installation bolt. General Description > COMPONENT">

2.CHECK OUTPUT OF STEERING ANGLE SENSOR USING SUBARU SELECT MONITOR.

1) Park the vehicle straight on a level surface.

2) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

3) Read the «Steering Angle Sensor» displayed on display.

Is the reading of «Steering Angle Sensor» −10 — 10°?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR">Go to Step 3.

Check the installation of steering angle sensor.

3.CHECK OUTPUT OF LATERAL G SENSOR AND LONGITUDINAL G SENSOR WITH SUBARU SELECT MONITOR.

1) Park the vehicle straight on a level surface.

2) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

3) Read the «Lateral G Sensor» «Longitudinal G Sensor» displayed on display.

Are the values of «Lateral G Sensor»«Longitudinal G Sensor» −2 — 2 m/s2?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR">Go to Step 4.

Recheck from step 1, and if the problem is not solved, Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR">Go to Step 7.

4.SET 0 POINT OF LATERAL G SENSOR AND LONGITUDINAL G SENSOR WITH SUBARU SELECT MONITOR.

1) Using the Subaru Select Monitor, select “Work Support”.

2) Perform the VDC sensor midpoint setting mode. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT">

Is the 0 point setting successful?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR">Go to Step 5.

Recheck from step 1, and when the 0 point setting is not possible, replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

5.PERFORM DRIVING TEST.

Drive approximately 10 minutes, and check if the warning lights illuminate or improperly operate during driving.

In a safe place, drive the vehicle while alternating acceleration and deceleration as much as possible.

Did the ABS warning light or VDC warning light remain off?
Does ABS or VDC operate without malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR">Go to Step 6.

Recheck from step 1, and when the warning lights illuminate or improperly operate, replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

6.CHECK OUTPUT OF LATERAL G SENSOR AND LONGITUDINAL G SENSOR WITH SUBARU SELECT MONITOR.

1) Park the vehicle on a level surface.

2) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

3) Read the «Lateral G Sensor» «Longitudinal G Sensor» displayed on display.

Are the values of «Lateral G Sensor»«Longitudinal G Sensor» −1.5 — 1.5 m/s2?

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Recheck from step 1, and if the problem is not solved, replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

7.CHECK OUTPUT OF LATERAL G SENSOR AND LONGITUDINAL G SENSOR WITH SUBARU SELECT MONITOR.

1) Remove the VDCCM&H/U installation bolt and bracket.

2) Keep VDCCM&H/U in a horizontal position.

3) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

4) Read the «Lateral G Sensor» «Longitudinal G Sensor» displayed on display.

When the VDCCM&H/U is in a horizontal position, are the values of «Lateral G Sensor»«Longitudinal G Sensor» −1.5 — 1.5 m/s2?

Check the bracket and brake pipe, and install VDCCM&H/U in a horizontal position to the vehicle.

Replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

Dtc c1721 yaw rate sensor

Dtc c1733 longitudinal g sensor

Other materials:

List of diagnostic trouble code (dtc) List
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > List of Diagnostic Trouble Code (DTC)LISTDTCItemReferenceB2300REAR RADAR CIRCUIT LOW Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2300 REAR RADAR CIRCUIT LOW">B2301REAR RADAR CIRCUIT HIGH Diagnostic Procedu ...

Third-row center seatbelt
Center seatbelt tongue plate Anchor tongue plate Anchor buckle Center seatbelt buckle WARNING In the Subaru Ascent, fastening a seatbelt with twisted webbing can significantly increase the risk and severity of injuries during a collision. When pulling the seatbelt from the ...

List of diagnostic trouble code (dtc) List
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > List of Diagnostic Trouble Code (DTC)LISTDTCItemContentReferenceU0073CONTROL MODULE COMMUNICATION BUS OFFDetected when CAN line abnormality is detected. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0073 CONTROL MODULE COMMUNICATION ...