Subaru Crosstrek Service Manual: Dtc b28b8 eyesight steering switch 1
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC B28B8 EyeSight STEERING SWITCH 1
Detected when EyeSight steering switch is not installed or has malfunction, or when the harness is faulty or open-circuited or in stuck ON condition.
DTC detecting condition:
• Wiring of the EyeSight steering switch is not connected.
• EyeSight steering switch circuit is open.
• EyeSight steering switch circuit stays ON.
Trouble symptom:
All functions of EyeSight system do not operate.
Wiring diagram:
EyeSight System EyeSight System > WIRING DIAGRAM">
| STEP | CHECK | YES | NO |
1.CHECK CURRENT DATA.
Confirm the current data «Cruise Control SW Voltage (Port14)» and «Cruise Control SW Voltage (Port16)» of EyeSight using Subaru Select Monitor. Read Current Data">
Does the display change according to the EyeSight steering switch operation?
Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.
NOTE:
In this case, temporary poor contact of connector, or temporary open or short circuit of harness may be the cause.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B28B8 EyeSight STEERING SWITCH 1">Go to Step 2.
2.CHECK HARNESS.
1) Disconnect the stereo camera connector and EyeSight steering switch connector.
2) Using the tester, measure the resistance between stereo camera connector and EyeSight steering switch connector.
Connector & terminal
(ST3) No. 4 — (R137) No. 16:
(ST3) No. 3 — (R137) No. 14:
(ST3) No. 9 — (R137) No. 15:
Is the resistance less than 1 ??
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B28B8 EyeSight STEERING SWITCH 1">Go to Step 3.
Repair or replace an open circuit in harness between the stereo camera connector and the EyeSight steering switch connector.
3.CHECK HARNESS.
Using the tester, measure the resistance between EyeSight steering switch connector and chassis ground.
Connector & terminal
(ST3) No. 4 — Chassis ground:
(ST3) No. 3 — Chassis ground:
(ST3) No. 9 — Chassis ground:
Is the resistance 1 M? or more?
Check the EyeSight steering switch. Switches and Harness">
Repair or replace the short circuit to ground in harness between the stereo camera connector and the EyeSight steering switch connector.
Dtc b28b7 ldp off switch
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B28B7 LDP OFF SWITCHDetected when lane departure warning OFF switch circuit is not installed, open-circuited, or ...
Dtc b28b9 eyesight steering switch 2
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B28B9 EyeSight STEERING SWITCH 2Detected when steering switch for EyeSight is not installed, is open-circuited or ...
Other materials:
Removal
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Expansion ValveREMOVAL1. Disconnect the ground cable from battery. NOTE">2. Using the refrigerant recovery system, discharge refrigerant. Refrigerant Recovery Procedure > PROCEDURE">3. Remove the air intake boot. Air Intake Boot > ...
Dtc u0122 lost communication with vehicle dynamics control module
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0122 LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULEDetected when CAN data from VDC CM does not arrive.NOTE:Perform the diagnosis for LAN system. Basic Diagnostic Pro ...
Adjustment
EXTERIOR BODY PANELS > Front DoorADJUSTMENTAdjust the clearance around the panel assembly - front door as follows.PartStandardAFender COMPL - front to Panel assembly - front door4.5±1.0 mm (0.18±0.04 in)BPanel assembly - front door to Side sill6.0+1.5, −1.0 mm (0.24+0.06, −0.04 in)C ...
