Subaru Crosstrek Service Manual: Diagnostic procedure without diagnostic trouble code (dtc) Check shift indicator
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure without Diagnostic Trouble Code (DTC)
CHECK SHIFT INDICATOR
Diagnosis:
• CAN communication is abnormal with the combination meter.
• Combination meter malfunction
Trouble symptom:
• Shift indicator does not display or remains displayed.
• Shift indicator display does not change.
| STEP | CHECK | YES | NO |
1.CHECK DTC.
Read the DTC relating the TCM using the Subaru Select Monitor.
Is DTC U0155 or U0423 displayed?
Perform the self-diagnosis of combination meter.
Diagnostic Procedure without Diagnostic Trouble Code (DTC) > CHECK SHIFT INDICATOR">Go to Step 2.
2.CHECK DTC.
Read the DTC relating the TCM using the Subaru Select Monitor.
Are DTCs other than U0155 and U0423 displayed?
Perform the diagnosis according to DTC.
Diagnostic Procedure without Diagnostic Trouble Code (DTC) > CHECK SHIFT INDICATOR">Go to Step 3.
3.CHECK COMBINATION METER.
Read DTC of combination meter.
Are any DTCs displayed?
Perform the diagnosis according to DTC.
Diagnostic Procedure without Diagnostic Trouble Code (DTC) > CHECK SHIFT INDICATOR">Go to Step 4.
4.CHECK TCM.
1) Operate the + side of the paddle shift switch.
2) Read the data of «Up Switch» using the Subaru Select Monitor.
Does it change between ON and OFF according to the operation?
Diagnostic Procedure without Diagnostic Trouble Code (DTC) > CHECK SHIFT INDICATOR">Go to Step 5.
Check for poor contact between TCM and paddle shift UP switch, and repair the defective part.
5.CHECK TCM.
1) Operate the − side of the paddle shift switch.
2) Read the data of «Down Switch» using the Subaru Select Monitor.
Does it change between ON and OFF according to the operation?
Diagnostic Procedure without Diagnostic Trouble Code (DTC) > CHECK SHIFT INDICATOR">Go to Step 6.
Check for poor contact between TCM and paddle shift down switch, and repair the defective part.
6.CHECK TCM.
1) Turn the ignition switch OFF, then turn it ON again.
2) Shift the select lever to manual mode.
3) Read the data of «Shift step in Manu. mode» using the Subaru Select Monitor.
Is “1” displayed?
Diagnostic Procedure without Diagnostic Trouble Code (DTC) > CHECK SHIFT INDICATOR">Go to Step 7.
Perform the diagnosis according to DTC P0951. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0951 AUTO SHIFT MANUAL CONTROL CIRCUIT RANGE/PERFORMANCE">
7.CHECK TCM.
1) Shift up the select lever.
2) Read the data of «Shift step in Manu. mode» using the Subaru Select Monitor.
Is “2” displayed?
Current condition is normal.
Replace the TCM. Transmission Control Module (TCM)">
Diagnostic procedure for subaru select monitor communication Communication for initializing impossible
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure for Subaru Select Monitor CommunicationCOMMUNICATION FOR INITIALIZING IMPOSSIBLEDiagnosis:Defective harness connectorTrouble ...
Diagnostics with phenomenon Inspection
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostics with PhenomenonINSPECTIONSymptomsFaulty partsEngine stalls when driving in “D” or “R” range, or selecting &ldq ...
Other materials:
Note
INSTRUMENTATION/DRIVER INFO > Combination Meter SystemNOTEFor procedure of each component in the combination meter system, refer to the respective section.• Combination meter assembly: Combination Meter">• Speedometer: Speedometer">• Tachometer: Tachometer&quo ...
Key replacement
Your key number plate will be required if
you ever need a replacement key made.
Any new key must be registered for use
with your vehicle's immobilizer system
before it can be used. The maximum
number of keys that can be registered
for use with one vehicle is as follows.
Four (models with ...
Installation
ENTERTAINMENT > Switches and HarnessINSTALLATION1. SATELLITE SWITCH ASSEMBLYCAUTION:• Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">• Do not a ...
