Subaru Crosstrek Service Manual: Component
EXHAUST(H4DO) > General Description
COMPONENT
1. FRONT EXHAUST PIPE AND CENTER EXHAUST PIPE
(1) | Front exhaust pipe | (12) | Front exhaust pipe lower cover | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Front catalytic converter | (13) | Front catalytic converter lower cover LH | T1: | 13 (1.3, 9.6) |
(3) | Center exhaust pipe | (14) | Front catalytic converter lower cover RH | T2: | 18 (1.8, 13.3) |
(4) | Rear catalytic converter | (15) | Front exhaust pipe side cover RH (front) | T3: | 23 (2.3, 17.0) |
(5) | Front oxygen (A/F) sensor | (16) | Front exhaust pipe side cover LH (front) | T4: | 30 (3.1, 22.1) |
(6) | Rear oxygen sensor | (17) | Front exhaust pipe side cover LH (rear) | T5: | 35 (3.6, 25.8) |
(7) | Gasket | (18) | Front exhaust pipe side cover RH (rear) | T6: | 42.5 (4.3, 31.3) |
(8) | Gasket | (19) | Center exhaust pipe upper cover | T7: | Front Oxygen (A/F) Sensor > INSTALLATION"> |
(9) | Front exhaust pipe upper cover | (20) | Band | T8: | Rear Oxygen Sensor > INSTALLATION"> |
(10) | Front catalytic converter upper cover LH | (21) | Hanger bracket (CVT model) | ||
(11) | Front catalytic converter upper cover RH | (22) | Hanger bracket (MT model) | ||
2. REAR EXHAUST PIPE AND MUFFLER
(1) | Gasket | (5) | Cushion rubber | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Spring | (6) | Self-locking nut | T: | 48 (4.9, 35.4) |
(3) | Chamber | (7) | Gasket | ||
(4) | Rear exhaust pipe | (8) | Muffler | ||
3. HEAT SHIELD COVER
(1) | Center exhaust cover | (2) | Rear exhaust cover | Tightening torque: N·m (kgf-m, ft-lb) | |
T1: | 10 (1.0, 7.4) | ||||
T2: | 18 (1.8, 13.3) | ||||
Caution
EXHAUST(H4DO) > General DescriptionCAUTION• Prior to starting work, pay special attention to the following:1. Always wear work clothes, a work cap, and protective shoes. Additionally, wear a ...
Muffler
...
Other materials:
Operation
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > AT OIL TEMP Warning Light DisplayOPERATIONThe AT OIL TEMP light illuminates or blinks, when the ATF temperature is high and malfunction occurs in CVT.• At normal conditionAfter turning the ignition switch to ON, illuminates for 2 seconds th ...
Inspection
WIPER AND WASHER SYSTEMS > Rear WasherINSPECTION1. VISUAL INSPECTIONCheck for the following items, and if any malfunction is found, replace the corresponding part.• Make sure the nozzle - rear washer and the hose - rear washer are not clogged.• Make sure the hose - rear washer is not ...
Installation
REAR SUSPENSION > Rear StabilizerINSTALLATIONCAUTION:• Be sure to use a new flange nut and self-locking nut.• Always tighten the bushing in the state where the vehicle is at curb weight and the wheels are in full contact with the ground.• Install the clamp - stabilizer bushing w ...
