Subaru Crosstrek Service Manual: Basic diagnostic procedure Procedure
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > Basic Diagnostic Procedure
PROCEDURE
1. COMBINATION METER
| STEP | CHECK | YES | NO |
1.PERFORM CUSTOMER INTERVIEW.
Using the Check List for Interview, ask the customer the condition of how trouble occurs. Check List for Interview > CHECK">
Did you interview the customer?
Basic Diagnostic Procedure > PROCEDURE">Go to Step 2.
Interview the customer. Check List for Interview > CHECK">
2.CHECK CAN COMMUNICATION.
Read the DTC of the CAN system using the Subaru Select Monitor. Read Diagnostic Trouble Code (DTC) > OPERATION">
Is DTC displayed?
Perform the diagnosis according to the basic diagnostic procedure for LAN system. Basic Diagnostic Procedure > PROCEDURE">
Basic Diagnostic Procedure > PROCEDURE">Go to Step 3.
3.CHECK COMBINATION METER.
Using the Subaru Select Monitor, read DTC of combination meter. Read Diagnostic Trouble Code (DTC)">
Is DTC displayed?
Record DTC and time stamp, and perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC) > LIST">
For time stamp, refer to “LAN SYSTEM”. General Description > CAUTION">
Basic Diagnostic Procedure > PROCEDURE">Go to Step 4.
4.CHECK COMBINATION METER.
Check the operation of combination meter. System Operation Check Mode">
Is it operating normally?
System is normal.
Replace the combination meter. Combination Meter">
2. MFD
| STEP | CHECK | YES | NO |
1.PERFORM CUSTOMER INTERVIEW.
Using the Check List for Interview, ask the customer the condition of how trouble occurs. Check List for Interview > CHECK">
Did you interview the customer?
Basic Diagnostic Procedure > PROCEDURE">Go to Step 2.
Interview the customer. Check List for Interview > CHECK">
2.CHECK CAN COMMUNICATION.
Read the DTC of the CAN system using the Subaru Select Monitor. Read Diagnostic Trouble Code (DTC) > OPERATION">
Is DTC displayed?
Perform the diagnosis according to the basic diagnostic procedure for LAN system. Basic Diagnostic Procedure > PROCEDURE">
Basic Diagnostic Procedure > PROCEDURE">Go to Step 3.
3.CHECK MFD.
Read the DTC relating the MFD using the Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">
Is DTC displayed?
Record DTC and time stamp, and perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC) > LIST">
For time stamp, refer to “LAN SYSTEM”. General Description > CAUTION">
Basic Diagnostic Procedure > PROCEDURE">Go to Step 4.
4.CHECK MFD.
Check the MFD display using the system operation check mode of combination meter. System Operation Check Mode">
Is the display normal?
System is normal.
Replace the MFD. Multi-function Display (MFD)">
Operation
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > User CustomizingOPERATION1. COMBINATION METER1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle ...
Check list for interview Check
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > Check List for InterviewCHECK• Inspect the following items regarding the vehicle’s state.• Print out this page for interviewing custome ...
Other materials:
List of diagnostic trouble code (dtc) List
AUTO HEADLIGHT BEAM LEVELER SYSTEM (DIAGNOSTICS) > List of Diagnostic Trouble Code (DTC)LISTDTCItemContent of diagnosisReferenceU0073CONTROL MODULE COMMUNICATION BUS OFFDetected when CAN line abnormality is detected. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0073 CONTROL M ...
Removal
LIGHTING SYSTEM > High-mounted Stop LightREMOVAL1. CROSSTREK MODEL1. Disconnect the ground cable from battery. NOTE">2. Remove the trim panel - rear gate UPR. Rear Gate Trim > REMOVAL">3. Remove the light assembly - high-mounted.(1) Remove the nut.(2) From the inside of the r ...
Installation
AIRBAG SYSTEM > Roll ConnectorINSTALLATIONCAUTION:If the steering wheel and steering angle sensor (steering roll connector) are removed, be sure to perform the following operations.• Align the center position of the steering roll connector.• Perform the neutral position setting of the ...
