Subaru Crosstrek Service Manual: Dtc u0420 invalid data received from power steering control module

DTC DETECTING CONDITION:

Defective data was transmitted from EPS CM.

TROUBLE SYMPTOM:

Cooperation control with EPS CM does not operate properly.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0420 INVALID DATA RECEIVED FROM POWER STEERING CONTROL MODULE">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0420 INVALID DATA RECEIVED FROM POWER STEERING CONTROL MODULE">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is DTC for the bus off or the data no-receive displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0420 INVALID DATA RECEIVED FROM POWER STEERING CONTROL MODULE">Go to Step 4.

4.CHECK DTC.

Check the displayed DTC.

Is U0420 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0420 INVALID DATA RECEIVED FROM POWER STEERING CONTROL MODULE">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0420 INVALID DATA RECEIVED FROM POWER STEERING CONTROL MODULE">Go to Step 9.

5.CHECK DTC.

1) Turn the ignition switch to OFF.

2) Disconnect the power steering CM connector.

3) Connect the disconnected connectors.

4) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0420 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0420 INVALID DATA RECEIVED FROM POWER STEERING CONTROL MODULE">Go to Step 6.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0420 INVALID DATA RECEIVED FROM POWER STEERING CONTROL MODULE">Go to Step 9.

6.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the electric power steering data abnormal detected in several modules?

Replace the power steering CM. Power Steering Control Module">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0420 INVALID DATA RECEIVED FROM POWER STEERING CONTROL MODULE">Go to Step 7.

7.REPLACE MODULE.

1) Replace the power steering CM.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0420 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0420 INVALID DATA RECEIVED FROM POWER STEERING CONTROL MODULE">Go to Step 8.

System is normal.

8.CHECK MODULE.

1) Reinstall the power steering CM.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0420 a current malfunction?

Replace the power steering CM. Power Steering Control Module">

System is normal.

9.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Using the Subaru Select Monitor, read DTC of CAN system. Read Diagnostic Trouble Code (DTC)">

Is U0420 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0420 INVALID DATA RECEIVED FROM POWER STEERING CONTROL MODULE">Go to Step 10.

10.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u0416 invalid data received from vehicle dynamics control module

Dtc u0422 invalid data received from body control module

Other materials:

Rear windows side seating position
Head restraint Release button To remove: While pressing the release button, pull out the head restraint. To install: Install the head restraint into the holes that are located on the top of the seatback until the head restraint locks. Press and hold the release button to lower t ...

Front wiring harness Location
WIRING SYSTEM > Front Wiring HarnessLOCATIONConnectorConnecting toNo.PoleColorAreaNo.DescriptionF51BlackC-1 HornF62C-1 Front fog light RH (without SRF)2BlackC-1 Front fog light RH (with SRF)F162C-1 Sub fan motorF172D-2 Main fan motorF212D-4 Front fog light LH (without SRF)2BlackD-4 Front fog ligh ...

Preparation tool
SECURITY AND LOCKS > General DescriptionPREPARATION TOOL1. SPECIAL TOOLILLUSTRATIONTOOL NUMBERDESCRIPTIONREMARKS — SUBARU SELECT MONITOR 4Used for setting of each function and troubleshooting for electrical system.NOTE:For detailed operation procedures of Subaru Select Monitor 4, refer to &ldqu ...