Subaru Crosstrek Service Manual: Dtc p0716 input/turbine shaft speed sensor "a" circuit range/performance

Subaru Crosstrek Service Manual / Continuously variable transmission (diagnostics) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p0716 input/turbine shaft speed sensor "a" circuit range/performance

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P0716 INPUT/TURBINE SHAFT SPEED SENSOR "A" CIRCUIT RANGE/PERFORMANCE

DTC detecting condition:

Immediately at fault recognition

Trouble symptom:

• No lock-up occurs.

• Shock occurs when selecting shift position.

• Shift control malfunction

STEP	CHECK	YES	NO

1.CHECK DTC.

Read the DTC using Subaru Select Monitor.

Besides DTC P0716, is DTC U0122 or U0416 displayed?

Perform the diagnosis according to DTCs other than P0716.

Perform the diagnosis according to DTC P0717. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0717 INPUT/TURBINE SHAFT SPEED SENSOR "A" CIRCUIT NO SIGNAL">

1. OUTLINE OF DIAGNOSIS

• Detect the malfunction of turbine speed sensor signal characteristics.

• Judge as NG if the turbine speed against the engine speed is outside the possible range considering the hardware capabilities.

2. EXECUTION CONDITION

Secondary parameters	Execution condition
12 V battery system voltage	≥ 10 V
Engine speed	≥ 400 rpm

3. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria	Threshold Value
Measured turbine shaft speed	< Table 1 rpm

Table 1

Engine speed (rpm)	3700	3727	3755	3782	3856	4019	4213	4456
Measured turbine shaft speed (rpm)	0	500	1000	1500	2000	2500	3000	3500

Engine speed (rpm)	4786	5213	5651	6101	6569	7044	7520
Measured turbine shaft speed (rpm)	4000	4500	5000	5500	6000	6500	7000

Time Needed for Diagnosis: 10 seconds

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p0713 transmission fluid temperature sensor "a" circuit high

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0713 TRANSMISSION FLUID TEMPERATURE SENSOR "A" CIRCUIT HIGHDTC detecting con ...

Dtc p0719 brake switch "b" circuit low

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0719 BRAKE SWITCH "B" CIRCUIT LOWDTC detecting condition:Immediately at faul ...

Other materials:

Steering system (power steering) Inspection
PERIODIC MAINTENANCE SERVICES > Steering System (Power Steering)INSPECTION1. STEERING WHEEL1. Set the steering wheel in a straight-ahead position, and check the wheel spokes to make sure they are correctly set in their specified positions.2. Lightly turn the steering wheel to the left and right t ...

Assembly
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Intake ManifoldASSEMBLY1. Install the fuel pipe and cap to the intake manifold.Tightening torque:6.4 N·m (0.7 kgf-m, 4.7 ft-lb)2. Install the fuel delivery pipe to the intake manifold.CAUTION:• Check that there is no damage or dust on the quick c ...

System maintenance
NOTE For the Subaru Ascent remote engine starter transceiver: if the vehicle battery has been replaced, discharged, or disconnected, it is necessary to start the vehicle manually at least once using the key or ignition system before the remote engine start function can be used again. This ste ...