Subaru Crosstrek Service Manual: Dtc p0560 system voltage

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p0560 system voltage

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P0560 SYSTEM VOLTAGE

DTC DETECTING CONDITION:

Immediately at fault recognition

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

WIRING DIAGRAM:

Engine electrical system Engine Electrical System">

STEP	CHECK	YES	NO

1.CHECK INPUT SIGNAL OF ECM.

1) Turn the ignition switch to OFF.

2) Measure the voltage between ECM connector and chassis ground.

Connector & terminal

(B137) No. 2 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Repair the poor contact of ECM connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0560 SYSTEM VOLTAGE">Go to Step 2.

2.CHECK HARNESS BETWEEN ECM AND MAIN FUSE BOX CONNECTOR.

1) Disconnect the connector from ECM.

2) Measure the resistance between ECM connector and chassis ground.

Connector & terminal

(B137) No. 2 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0560 SYSTEM VOLTAGE">Go to Step 3.

Repair the short circuit to ground in harness between ECM connector and battery terminal.

3.CHECK FUSE NO. 13 (MAIN FUSE BOX).

Is the fuse blown out?

Replace the fuse.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

• Open circuit in harness between ECM connector and battery

• Poor contact of ECM connector

• Poor contact of battery terminal

1. OUTLINE OF DIAGNOSIS

Detect the open/short circuit of back-up power supply circuit.

Judge as NG when the backup power voltage is low.

2. EXECUTION CONDITION

Secondary Parameters	Execution condition
Battery voltage	≥ 10.9 V

3. GENERAL DRIVING CYCLE

Always perform the diagnosis continuously.

4. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria	Threshold Value
Voltage of back-up power supply	≤ 3.5 V

Time Needed for Diagnosis: 2500 ms

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p0125 insufficient coolant temperature for closed loop fuel control

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0125 INSUFFICIENT COOLANT TEMPERATURE FOR CLOSED LOOP FUEL CONTROLDTC detecting condition:Detected when two ...

Dtc u0122 lost communication with vehicle dynamics control module

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0122 LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULENOTE:For the diagnostic procedure, refer to LAN ...

Other materials:

Removal
EXTERIOR BODY PANELS > Door Sash TapeREMOVAL1. FRONT DOOR1. Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. NOTE">2. Remove the trim panel - front door. Door Trim > REMOVAL">3. Remove the outer mirror assembly. Outer Mirror Ass ...

Engine hood
CAUTION When you open the engine hood, do not stand the wiper blades up. Furthermore, while the hood is open, do not operate the windshield wipers. Doing so could result in damage to the engine hood and wiper blades. Be extremely careful not to catch fingers or other objects wh ...

Uniform tire quality grading standards
The Uniform Tire Quality Grading (UTQG) system provides valuable comparative information about tire performance, specifically in the areas of treadwear, traction, and temperature resistance. For Subaru Ascent owners, understanding these ratings can help in selecting the most suitable tires for ...