HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Refrigerant Leak Check
INSPECTION
1. Attach the manifold gauge set.
Preparation tool:
Manifold gauge set
(1) Check that all valves are fully closed.
(2) Install the low/high pressure hoses to the service ports on the low/high pressure sides of the vehicle respectively.
CAUTION:
Confirm that the connections are secure.
(3) Start the engine, operate the A/C system for approx. 10 minutes, and check that the high-pressure side indicates 0.69 MPa (7.0 kgf/cm2, 100 psi) or more.
2. Turn the ignition switch to OFF to start the leak test.
Preparation tool:
Electronic leak detector (leak tester)
Items | Condition | Corrective action |
Pipe | Check the connections of pipe and expansion valve. | Check the O-ring at connection and tightening torque. If necessary, replace each part. |
Check the connection between pressure switch or pressure sensor and high-pressure pipe. | Replace the pressure switch or pressure sensor. | |
Check the connection between pipe and condenser. | Check the O-ring at connection and tightening torque. If necessary, replace each part. | |
Condenser | Check the welded part of condenser and core. | Replace the condenser. |
Hose (high-pressure) | Check the connection between hose (high-pressure) and compressor. | Check the O-ring at connection and tightening torque. If necessary, replace each part. |
Check the connection between hose (high-pressure) and condenser. | Check the O-ring at connection and tightening torque. If necessary, replace each part. | |
Check the rubber part of the flexible hose and pipe seam. CAUTION: |
Carefully check the external surface of flexible hoses and pipes at approx. 25 mm (0.98 in) per second.
Replace the hose (high pressure).
Check the valve and cap in the service port.
Check the rubber seal of the valve and cap. If necessary, replace valve or cap.
Compressor
Check the compressor pulley and vicinity of shaft seal.
CAUTION:
Some shaft seals will show a slight amount of leakage, about 3 g (0.1 oz) per year. This is not a problem.
Replace the compressor.
Hose (low-pressure)
Check the connection between hose (low pressure) and expansion valve.
Check the O-ring at connection and tightening torque. If necessary, replace each part.
Check the connection between hose (low pressure) and compressor.
Check the O-ring at connection and tightening torque. If necessary, replace each part.
Check the rubber part of the flexible hose and pipe seam.
CAUTION:
Carefully check the external surface of flexible hoses and pipes at approx. 25 mm (0.98 in) per second.
Replace the hose (low pressure).
Check the valve and cap in the service port.
Check the rubber seal of the valve and cap. If necessary, replace valve or cap.
Evaporator
Remove the drain hose from the heater case, and check the end part for 10 seconds or more.
Replace the evaporator.
Check the air vent grille.
NOTE:
Turn the ignition switch to ON, and run the blower at high speed for approx. 1 minute. Stop the blower to check the air vent grille on the instrument panel. While moving the tester closer to the grille, run the blower for 1 or 2 seconds, then stop it. Check the grille at that position for at least 10 seconds.
Replace the evaporator.
Diagnostics with phenomenon Inspection
AUTO HEADLIGHT BEAM LEVELER SYSTEM (DIAGNOSTICS) > Diagnostics with PhenomenonINSPECTION1. BEAM LEVEL CONTROL DOES NOT FUNCTIONCAUTION:• Before performing diagnosis, check the fuse in this circuit.• Initialization is required after replacing the auto headlight beam leveler CM.Wiring d ...
Precautions when working with the parts mounted on the vehicle
WIRING SYSTEM > Working PrecautionsPRECAUTIONS WHEN WORKING WITH THE PARTS MOUNTED ON THE VEHICLE1. When working under a vehicle which is jacked-up, always be sure to use rigid rack.2. The parking brake must always be applied during working. Also, in automatic transmission vehicles, keep the sele ...
Dtc u0151 lost communication with restraints control module
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0151 LOST COMMUNICATION WITH RESTRAINTS CONTROL MODULEDetected when CAN data is not received from airbag CM.NOTE:Perform the diagnosis for LAN system. Basic Diagnostic Procedure > PROCEDURE ...