Subaru Crosstrek Service Manual: System operation check mode Operation

Subaru Crosstrek Service Manual / Keyless access with push button start system (diagnostics) / System operation check mode Operation

KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > System Operation Check Mode

OPERATION

1. On «Start» display, select «Diagnosis».

2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».

3. On «Main Menu» display, select «Each System».

4. On «Select System» display, select «Keyless Access with Push Button Start» and then select «Enter».

5. On «Select Function» display, select «Active Test».

6. Select a location to be inspected.

NOTE:

Each output check continues to run for five seconds before stopping automatically.

Data	Keyless access CM output check	Remarks
Tuner power supply ON (indoor tuner)	Output	Perform the power supply check for the receiver.
Tuner power supply ON (indoor tuner)	Stop	Perform the power supply check for the receiver.
Driver’s external transmitter	Output	Perform the output check for the driver’s side door outside antenna.
Driver’s external transmitter	Stop
Passenger’s external transmitter	Output	Perform the output check for the passenger’s side door outside antenna.
Passenger’s external transmitter	Stop
STSW	Output	Turn on the STSW. *2
STSW	Stop	Turn on the STSW. *2
IGN2	Output	Turn on the IGN2.
IGN2	Stop	Turn on the IGN2.
IGN1	Output	Turn on the IGN1.
IGN1	Stop	Turn on the IGN1.
ACC	Output	Turn on the ACC.
ACC	Stop	Turn on the ACC.
Start SW character illumination lighted	Output	Perform ON output of the push button ignition switch back-up light. *1
Start SW character illumination lighted	Stop
Start SW indicator lighted (green)	Output	Perform ON output of the push button ignition switch back-up light. *1
Start SW indicator lighted (green)	Stop
Start SW indicator lighted (orange)	Output	Perform ON output of the push button ignition switch back-up light. *1
Start SW indicator lighted (orange)	Stop
Steering lock power supply	Output	Output power supply signal from power supply CM to steering lock CM.
Steering lock power supply	Stop

*1: When lit by a condition other than for a system operation check mode, it will not become unlit even when set to OFF or no output.

*2: When performed with ignition switch ON, engine will start. Therefore, great care must be exercised.

NOTE:

For detailed operation procedures, refer to “Application help”.

Read diagnostic trouble code (dtc) Operation

KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Read Diagnostic Trouble Code (DTC)OPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the ...

Lan system (diagnostics)

...

Other materials:

Installation
STARTING/CHARGING SYSTEMS(H4DO) > StarterINSTALLATIONInstall in the reverse order of removal.NOTE:• For CVT model, a nut is used at (a).• Tighten the starter and cable stay (b) together using the upper bolt securing the starter.Tightening torque:T1: 14 N·m (1.4 kgf-m, 10.3 ft-l ...

Installation
EXTERIOR BODY PANELS > Rear DoorINSTALLATION1. REAR DOOR PANEL1. Put a wooden block on a jack and place the panel assembly - rear door on it.2. Apply grease to the moving part of door hinges.3. Adjust the height by the jack, and temporarily install the panel assembly - rear door to the upper hing ...

Dtc b16f8 satellite safing sensor recognition error
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B16F8 SATELLITE SAFING SENSOR RECOGNITION ERRORDiagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting condition:• Satellite safing sensor is misinstalled.• Airbag control module is faulty.STEPCHECKYE ...