Subaru Crosstrek Owners Manual: Switching power status
- Operation indicator
- Push-button ignition switch
The power status is switched every time the push-button ignition switch is pressed.
1. Carry the access key, and sit in the driver's seat.
2. Shift the select lever into the "P" position.
3. Press the push-button ignition switch without depressing the brake pedal. Every time the button is pressed, the power is switched in the sequence of "OFF", "ACC", "ON" and "OFF". When the engine is stopped and the push-button ignition switch is in "ACC" or "ON", the operation indicator on the push-button ignition switch illuminates in orange.
| Power status | Indicator color | Operation |
| OFF | Turned off | Power is turned off. |
| ACC | Orange | The following systems can be used: audio and accessory power outlet. |
| ON | Orange (while engine is stopped) | All electrical systems can be used. |
| Turned off (while engine is running) |
CAUTION
To prevent the vehicle battery from discharging, do not leave the push-button ignition switch in the "ON" or "ACC" position for a long time.
To avoid a malfunction, observe the following precautions.
- Do not spill drinks or other liquids on the push-button ignition switch.
- Do not touch the push-button ignition switch with a hand that is soiled with oil or other contaminants.
If the push-button ignition switch does not operate smoothly, stop the operation. Contact a SUBARU dealer immediately.
If the push-button ignition switch does not illuminate even when the instrument panel illumination is turned on, have the vehicle inspected at a SUBARU dealer.
If the vehicle was left in the hot sun for a long time, the surface of the push-button ignition switch may get hot. Be careful not to burn yourself.
NOTE
- When operating the push-button ignition switch, firmly press it all the way.
- If the push-button ignition switch is pressed quickly, the power may not turn on or off.
- If the indicator light on the pushbutton ignition switch flashes in green when the push-button ignition switch is pressed, steering is locked. When this occurs, press the push-button ignition switch while turning the steering wheel left and right.
Battery drainage prevention function
When the push-button ignition switch is left in the "ACC" or "ON" position for approximately 1 hour, the push-button ignition switch will be automatically switched to "OFF" to prevent the battery from going dead. This function is activated when the select lever is in the "P" position.
When access key does not operate properly
Refer to "Access key - if access key does not operate properly"
Operating range for push-button start system
Antenna
Operating range
NOTE
If the access key is not detected
within the operating range of the antennas
inside the vehicle, the pushbutton
ignition switch and the engine
start canno ...
Hazard warning flasher
Models without multi function display
Models with multi function display
The hazard warning flasher is used to
warn other drivers when you have to park your vehicle under emergency
condit ...
Other materials:
Steering system (power steering) Inspection
PERIODIC MAINTENANCE SERVICES > Steering System (Power Steering)INSPECTION1. STEERING WHEEL1. Set the steering wheel in a straight-ahead position, and check the wheel spokes to make sure they are correctly set in their specified positions.2. Lightly turn the steering wheel to the left and right t ...
Rear windows side seating position
Head restraint
Release button
To remove:
While pressing the release button, pull out
the head restraint.
To install:
Install the head restraint into the holes that
are located on the top of the seatback until
the head restraint locks. Press and hold
the release button to lower t ...
Component
EXHAUST(H4DO) > General DescriptionCOMPONENT1. FRONT EXHAUST PIPE AND CENTER EXHAUST PIPE(1)Front exhaust pipe(12)Front exhaust pipe lower coverTightening torque: N·m (kgf-m, ft-lb)(2)Front catalytic converter(13)Front catalytic converter lower cover LHT1:13 (1.3, 9.6)(3)Center exhaust pip ...
