Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Removal

AIRBAG SYSTEM > Passenger’s Airbag Module

REMOVAL

CAUTION:

Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">

1. Turn the ignition switch to OFF.

2. Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. NOTE">

NOTE:

On CVT models, shift the select lever into “N” before disconnecting the battery ground cable.

3. Remove the console box assembly, the cover - shift lever and the panel center LWR on the RH and LH sides. Console Box > REMOVAL">

4. Remove the cover - instrument panel side LH and the cover assembly - instrument panel LWR driver. Instrument Panel Lower Cover > REMOVAL">

5. Remove the cover switch - starter. (Models without the keyless access with push button start)

(1) Release the claws and remove the cover switch - starter.

(2) Disconnect the connector and aspirator hose.

6. Remove the panel - switch. (Model with keyless access with push button start)

(1) Release the claw of the switch - push button start, and disconnect the connector.

(2) Release the claws, and then remove the panel - switch.

(3) Disconnect the connector and aspirator hose.

7. Remove the knee airbag module. Knee Airbag Module > REMOVAL">

8. Release the clips and claws, then detach the left and right grille speaker side.

NOTE:

Remove the grille speaker side by using a plastic remover.

9. Remove the trim panel - front pillar UPR on the left and right sides. Upper Inner Trim > REMOVAL">

10. Remove the glove box assembly. Glove Box > REMOVAL">

11. On manual A/C models, disconnect the control cables from both sides of the heater & cooling unit.

12. Remove the center grille assembly. Air Vent Grille > REMOVAL">

13. Remove the audio assembly or navigation assembly. Audio > REMOVAL">

14. Remove the multi-function display assembly. Multi-function Display (MFD) > REMOVAL">

15. Remove the combination meter assembly. Combination Meter > REMOVAL">

16. Disconnect the passenger’s airbag module connector. Airbag Connector > PROCEDURE">

17. Remove the column assembly - steering. Steering Column > REMOVAL">

18. Remove the cover side sill - front INN and cover side sill - front on the RH and LH side. Lower Inner Trim > REMOVAL">

19. Remove the body side weather strip - flange front.

20. Remove the instrument panel assembly and the beam COMPL - steering as a unit. Instrument Panel Assembly > REMOVAL">

21. Remove the screws and remove the front (A) and side vent duct LH/RH (B).

22. Separate the panel COMPL - instrument and the beam COMPL - steering.

(1) Remove the clamps and bolts of the passenger’s airbag module harness.

(2) Remove the left and right speakers and the sunload sensor.

NOTE:

Detach the harness clamp together.

(3) Disconnect the front accessory socket connector.

(4) Remove the nut (a) and screws (b), (c), (d), (e), (f), (g) and (h).

(5) While being careful with the harness, separate the panel COMPL - instrument and the beam COMPL - steering.

23. Remove the claws, and remove the passenger’s airbag module.

24. For handling of the removed airbag module, refer to “CAUTION”. General Description > CAUTION">

Installation
AIRBAG SYSTEM > Passenger’s Airbag ModuleINSTALLATIONCAUTION:• Before handling the airbag system components, refer to “CAUTION” of “General Description” in &ldqu ...

Roll connector
...

Other materials:

Front differential gear oil (CVT models) and rear differential gear oil
It is not necessary to check the gear oil level. Check that there are no cracks, damage or leakage. However, the oil inspection should be performed according to the maintenance schedule in the "Warranty and Maintenance Booklet". Consult your SUBARU dealer for details. Recommended grade and ...

Location
ENTERTAINMENT > General DescriptionLOCATION1. AUDIO AND NAVIGATION SYSTEM(1)Telematics sub antenna(3)Speaker ASSY - tweeter front LH(5)Data communication module(2)GPS antenna ASSY(4)Audio ASSY or navigation ASSY(6)Speaker ASSY - tweeter front RH*1: Model with telematics(1)Telematics antenna(4)Fro ...

Installation
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Reverse Brake AssemblyINSTALLATION1. Select a washer. Forward Clutch Assembly > ADJUSTMENT">2. Install the selected washer to the reverse brake housing.3. Install the thrust bearing to the reverse brake housing.NOTE:Face the temper color sur ...

© 2016-2024 Copyright www.sucross.com