Subaru Crosstrek Service Manual: Removal

1. MODELS WITHOUT EyeSight

1. Disconnect the ground cable from battery. NOTE">

2. Remove the air intake boot. Air Intake Boot > REMOVAL">

CAUTION:

Move aside the intake boot to perform the operation without disconnecting the PCV hose.

3. Remove the VDC control module & hydraulic control unit (VDCCM&H/U).

(1) Remove any dirt from around the VDCCM&H/U.

(2) Pull up the lock lever (b) while pressing the lock button (a) and disconnect the VDCCM&H/U connector.

CAUTION:

Do not pull on the harness when disconnecting the connector.

(3) Using a flare nut wrench, disconnect each brake pipe from VDCCM&H/U.

CAUTION:

• Wrap the brake pipe with a vinyl bag so as not to spill the brake fluid on the painted surface of the vehicle body.

• If brake fluid is spilled on the painted surface of the vehicle body, wash it off immediately with water and wipe clean.

(4) Remove the nuts and remove the VDCCM&H/U from the bracket - hydraulic unit.

CAUTION:

• Do not drop or bump the VDCCM&H/U.

• Do not turn the VDCCM&H/U upside down or place it sideways for storage.

• Be careful not to let foreign matter enter the VDCCM&H/U.

• Be careful that no water and fluid enter the connectors.

• Avoid unnecessary removal of parts in order to prevent fluid leakage.

• When the VDCCM&H/U components are removed, be sure to perform the installation according to the installation procedures. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > INSTALLATION">

1. Disconnect the ground cable from battery. NOTE">

2. Remove the air intake boot. Air Intake Boot > REMOVAL">

3. Remove the VDC control module & hydraulic control unit (VDCCM&H/U).

(1) Remove any dirt from around the VDCCM&H/U.

(2) Push the lock button (a), pull down the lock lever (b) and disconnect the VDCCM&H/U connector.

CAUTION:

Do not pull on the harness when disconnecting the connector.

(3) Using a flare nut wrench, disconnect each brake pipe from VDCCM&H/U.

CAUTION:

• Wrap the brake pipe with a vinyl bag so as not to spill the brake fluid on the painted surface of the vehicle body.

• If brake fluid is spilled on the painted surface of the vehicle body, wash it off immediately with water and wipe clean.

(4) Using a flare nut wrench, disconnect pipes (A) and (B) from VDCCM&H/U.

(5) Remove the bolt, and remove the VDCCM&H/U from the bracket - hydraulic unit.

CAUTION:

• Do not drop or bump the VDCCM&H/U.

• Do not turn the VDCCM&H/U upside down or place it sideways for storage.

• Be careful not to let foreign matter enter the VDCCM&H/U.

• Be careful that no water and fluid enter the connectors.

Installation

Vdc off switch

Other materials:

Removal
COOLING(H4DO) > Radiator Main Fan and Fan MotorREMOVAL1. Disconnect the ground cable from battery. NOTE">2. Remove the reservoir tank. Reservoir Tank > REMOVAL">3. Disconnect the connector from the main fan motor assembly.4. Remove the bolts which hold the radiator main fan s ...

Electrical specification
AIRBAG SYSTEM (DIAGNOSTICS) > Airbag Control Module I/O SignalELECTRICAL SPECIFICATION• Terminal numbers in airbag control module connector are shown in the figure.• The airbag warning light illuminates when the connector is removed from the airbag control module.ItemControl module te ...

Removal
BRAKE > Front Disc Brake AssemblyREMOVALCAUTION:Do not allow brake fluid to come in contact with the painted surface of the vehicle body. If it does, wash off with water and wipe away completely.1. Lift up the vehicle, and then remove the front wheels.2. Remove the caliper body assembly.(1) Remov ...