Subaru Crosstrek Service Manual: Removal
MECHANICAL(H4DO) > Cylinder Head
REMOVAL
1. CYLINDER HEAD RH
1. Remove the engine from the vehicle. Engine Assembly > REMOVAL">
2. Remove the intake manifold. Intake Manifold > REMOVAL">
3. Remove the engine wiring harness. Engine Wiring Harness > REMOVAL">
4. Remove the tumble generator valve assembly RH. Tumble Generator Valve Assembly > REMOVAL">
5. Remove the chain cover. Chain Cover > REMOVAL">
6. Remove the rocker cover RH. Rocker Cover > REMOVAL">
7. Remove the cam carrier RH. Cam Carrier > REMOVAL">
8. Remove the EGR cooler. EGR Cooler > REMOVAL">
9. Loosen the bolts holding the cylinder head RH equally, a little at a time in numerical sequence as shown in the figure, and while leaving the cylinder head bolts (1) and (4) engaged by three or four threads, remove the other cylinder head bolts.
NOTE:
Leaving the cylinder head bolts (1) and (4) engaged by three or four threads prevents the cylinder head RH from falling.
10. While tapping the cylinder head RH with a plastic hammer, separate it from cylinder block RH.
11. Remove the bolts (1) and (4) to remove cylinder head RH.
12. Remove the cylinder head gasket RH.
CAUTION:
Be careful not to scratch the mating surface of cylinder head and cylinder block.
13. Remove the liquid gasket from cylinder head RH and cam carrier RH.
2. CYLINDER HEAD LH
1. Remove the engine from the vehicle. Engine Assembly > REMOVAL">
2. Remove the intake manifold. Intake Manifold > REMOVAL">
3. Remove the engine wiring harness. Engine Wiring Harness > REMOVAL">
4. Remove the tumble generator valve assembly LH. Tumble Generator Valve Assembly > REMOVAL">
5. Remove the chain cover. Chain Cover > REMOVAL">
6. Remove the rocker cover LH. Rocker Cover > REMOVAL">
7. Remove the cam carrier LH. Cam Carrier > REMOVAL">
8. Remove the A/C compressor. Compressor > REMOVAL">
9. Loosen the bolts holding the cylinder head LH equally, a little at a time in numerical sequence as shown in the figure, and while leaving the cylinder head bolts (1) and (4) engaged by three or four threads, remove the other cylinder head bolts.
NOTE:
Leaving the cylinder head bolts (1) and (4) engaged by three or four threads prevents the cylinder head LH from falling.
10. While tapping the cylinder head LH with a plastic hammer, separate it from cylinder block LH.
11. Remove the cylinder head bolts (1) and (4) to remove cylinder head LH.
12. Remove the cylinder head gasket LH.
CAUTION:
Be careful not to scratch the mating surface of cylinder head and cylinder block.
13. Remove the liquid gasket from cylinder head LH and cam carrier LH.
Assembly
MECHANICAL(H4DO) > Cylinder HeadASSEMBLY(1)Exhaust valve(6)Valve spring(11)Intake valve guide(2)Intake valve(7)Valve spring retainer(12)Exhaust valve guide(3)Cylinder head(8)Valve collet(13)Roller ...
Disassembly
MECHANICAL(H4DO) > Cylinder HeadDISASSEMBLY1. Remove the chain cover securing bolt from the cylinder head LH.2. Remove the stud bolts from the cylinder head.3. Remove the valve collet, valve, valve ...
Other materials:
Dtc p0203 cylinder 3 injector "a" circuit
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0203 CYLINDER 3 INJECTOR "A" CIRCUITNOTE:For the diagnostic procedure, refer to DTC P0201. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0201 CYLINDER 1 INJECTOR "A" C ...
Inspection
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Throttle BodyINSPECTION1. THROTTLE SENSOR (METHOD WITH CIRCUIT TESTER)1. Remove the glove box. Glove Box > REMOVAL">2. Turn the ignition switch to ON. (engine OFF)3. Measure the voltage between ECM connector terminals.(A)To ECM connector Thrott ...
List of diagnostic trouble code (dtc) List
POWER ASSISTED SYSTEM (POWER STEERING) (DIAGNOSTICS) > List of Diagnostic Trouble Code (DTC)LISTDTCItemContent of diagnosisNoteNoneWithout DTCNormal Subaru Select Monitor > INSPECTION">“Assist limitation” is displayed in the current data «EPS operating condition».Assist l ...
