Subaru Crosstrek Service Manual: Removal
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Air Vent Grille
REMOVAL
1. CENTER GRILLE ASSEMBLY
CAUTION:
• Do not put your finger on the fin of the air vent grille. Doing so may damage the fin.
• Always pull the center grille assembly toward you slowly. If attempting to remove by turning it upward, the claws and connectors may be damaged.
1. Disconnect the ground cable from battery. NOTE">
2. Remove the center grille assembly.
(1) Attach the protective tape (a) to the instrument panel assembly.
(2) Release the claw by using a clip remover wrapped with protective tape.
(3) Disconnect the connector and remove the center grille assembly.
3. Release the claws, and then remove the grille assembly - CTR ventilation from the center grille assembly.
2. SIDE GRILLE ASSEMBLY
LH side
1. Disconnect the ground cable from battery. NOTE">
2. Remove the cover assembly - instrument panel LWR driver OUT. Instrument Panel Lower Cover > REMOVAL">
3. Remove the grille assembly - ventilation LH.
CAUTION:
• When using a flat tip screwdriver, apply protective tape or cloth and be careful not to cause damage.
• Do not pull the grille assembly - ventilation forcibly. Doing so may cause deformation or damage.
(1) Push the claw (a) on the outlet dial side upward from the back of the instrument panel assembly.
(2) While pushing, pull the grille assembly - ventilation toward you to release the claw.
(3) Release the other claw (b) in the same manner, then remove the grille assembly - ventilation LH.
RH side
1. Disconnect the ground cable from battery. NOTE">
2. Remove the pocket assembly and the back panel - pocket. Glove Box > REMOVAL">
3. Remove the grille assembly - ventilation RH.
CAUTION:
• When using a flat tip screwdriver, apply protective tape or cloth and be careful not to cause damage.
• Do not pull the grille assembly - ventilation forcibly. Doing so may cause deformation or damage.
(1) Push the claw (a) on the outlet dial side upward from the back of the instrument panel assembly.
(2) While pushing, pull the grille assembly - ventilation toward you to release the claw.
(3) Release the other claw (b) in the same manner, then remove the grille assembly - ventilation RH.
Inspection
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Air Vent GrilleINSPECTION1. Check that the direction and amount of air can be adjusted smoothly. Replace the grille assembly - ventilation if faulty.2. Ch ...
Installation
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Air Vent GrilleINSTALLATIONCAUTION:After installing the center grille assembly or grille assembly - ventilation, check that the air vent grille is inserte ...
Other materials:
Removal
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Oil PumpREMOVAL1. Remove the transmission assembly from the vehicle. Automatic Transmission Assembly > REMOVAL">2. Remove the torque converter assembly. Torque Converter Assembly > REMOVAL">3. Remove the oil pump chain cover. Oi ...
Adjustment
DIFFERENTIALS > Rear Differential (VA-type)ADJUSTMENT1. SIDE GEAR BACKLASHAdjust the side gear backlash. Rear Differential (VA-type) > ASSEMBLY">2. HYPOID DRIVEN GEAR BACKLASHAdjust hypoid driven gear backlash. Rear Differential (VA-type) > ASSEMBLY">3. TOOTH CONTACT BETWE ...
Installation
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Transmission Mounting SystemINSTALLATION1. PITCHING STOPPER1. Install the pitching stopper.Tightening torque:T1: 50 N·m (5.1 kgf-m, 36.9 ft-lb)T2: 58 N·m (5.9 kgf-m, 42.8 ft-lb)2. Install the air intake boot. Air Intake Boot > INSTALLA ...
