FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Engine Wiring Harness
REMOVAL
1. Release the fuel pressure. Fuel > PROCEDURE">
2. Disconnect the ground cable from battery.
3. Remove the intake manifold. Intake Manifold > REMOVAL">
4. Disconnect the connector from the engine.
• Structural diagram 1
(1) | Tumble generator valve actuator RH | |
(2) | Engine harness connector (16P) | |
(3) | Engine harness connector (54P) | |
(4) | Throttle position sensor connector | |
(5) | Manifold absolute pressure sensor connector | |
(6) | Engine ground (2 locations) | |
(7) | Crankshaft position sensor | |
(8) | Knock sensor | |
(9) | Purge control solenoid valve connector | |
(10) | Tumble generator valve actuator LH | |
(11) | Fuel injector (#4) | |
(12) | Fuel injector (#2) | |
(13) | Engine coolant temperature sensor | |
(14) | Remove the clip from the screw hole. | |
(15) | Fuel injector (#1) | |
(16) | EGR valve | |
(17) | Fuel injector (#3) | |
(18) | Oil pressure switch | |
(19) | Engine oil temperature sensor | |
(20) | Intake camshaft position sensor LH | |
(21) | Intake oil control solenoid LH | |
(22) | Remove the clip from the screw hole. | |
(23) | Remove the clip from the screw hole. | |
(24) | Exhaust oil control solenoid LH | |
(25) | Remove the clip from the screw hole. | |
(26) | Exhaust camshaft position sensor LH | |
(27) | Remove the clip from the oval hole. | |
(28) | Exhaust camshaft position sensor RH | |
(29) | Remove the clip from the screw hole. | |
(30) | Exhaust oil control solenoid RH | |
(31) | Remove the clip from the screw hole. | |
(32) | Intake oil control solenoid RH | |
(33) | Intake camshaft position sensor RH | |
(34) | Remove the clip from the screw hole. | |
(35) | Oil level switch connector |
• Structural diagram 2
(1) | Remove the clip from the screw hole. | |
(2) | Ignition coil No. 4 | |
(3) | Ignition coil No. 2 | |
(4) | Remove the clip from the screw hole. | |
(5) | Ignition coil No. 3 | |
(6) | Ignition coil No. 1 | |
(7) | Front oxygen (A/F) sensor | |
(8) | Rear oxygen sensor |
5. Remove the engine wiring harness.
Electrical specification
TIRE PRESSURE MONITORING SYSTEM (DIAGNOSTICS) > Control Module I/O SignalELECTRICAL SPECIFICATIONTerminal No.ContentMeasured value and measuring conditionsRemarks1 — — — 2 — — — 3 — — — 4Ignition power supply10 — 13 V (when the ignition switch is ON) — 5GND0 V (always) ...
Installation
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Transmission Control DeviceINSTALLATION1. Install the parking support.Tightening torque:25 N·m (2.5 kgf-m, 18.4 ft-lb)2. Install the extension case. Extension Case > INSTALLATION">3. Install the manual valve.4. Install the parking rod ...
Check adaptive cruise control indicator light/constant speed cruise control indicator light and cruise set indicator light
EyeSight (DIAGNOSTICS) > Diagnostics with PhenomenonCHECK ADAPTIVE CRUISE CONTROL INDICATOR LIGHT/CONSTANT SPEED CRUISE CONTROL INDICATOR LIGHT AND CRUISE SET INDICATOR LIGHTTROUBLE SYMPTOM:Adaptive cruise control or conventional cruise control can be set, but adaptive cruise control indicator li ...