Subaru Crosstrek Service Manual: Removal
COOLING(H4DO) > Thermostat
REMOVAL
1. ENGINE SIDE
1. Disconnect the ground cable from battery. NOTE">
2. Lift up the vehicle.
3. Remove the under cover. Front Under Cover > REMOVAL">
4. Drain engine coolant. Engine Coolant > REPLACEMENT">
5. Remove the front exhaust pipe. Front Exhaust Pipe > REMOVAL">
6. Disconnect the radiator outlet hose from thermostat cover.
7. Remove the thermostat cover, and then remove the thermostat.
(A) | Thermostat cover | (B) | Gasket | (C) | Thermostat |
8. Remove the gasket from thermostat.
2. CVTF COOLER (WITH WARMER FEATURE) SIDE
1. Disconnect the ground cable from battery. NOTE">
2. Lift up the vehicle.
3. Remove the under cover. Front Under Cover > REMOVAL">
4. Drain engine coolant. Engine Coolant > REPLACEMENT">
5. Lower the vehicle.
6. Remove the clip (A) from the air intake boot.
7. Loosen the clamp (B) securing the air cleaner case (rear) to the air intake boot.
8. Loosen the clamp (C) which secures the throttle body to the air intake boot.
9. Remove the air intake boot from the throttle body, and place the air intake boot aside so that it does not interfere with the work.
10. Disconnect the engine harness connector.
(1) Remove the bolt securing the bulkhead harness connector bracket.
(2) Disconnect the bulkhead harness connector from the engine harness connector (black) and engine harness connector (brown).
11. Disconnect the connector (A) from manifold absolute pressure sensor.
12. Disconnect the connector (B) from the throttle position sensor.
13. Disconnect the connector (C) from the EGR control valve.
14. Remove the bolt securing the engine hanger from the cylinder block RH, and place it aside so that it does not interfere with the work.
15. Disconnect the engine coolant hose from the thermostat cover.
16. Remove the thermostat cover, and then remove the thermostat.
(A) | Thermostat cover | (B) | Gasket | (C) | Thermostat |
17. Remove the gasket from thermostat.
Inspection
COOLING(H4DO) > ThermostatINSPECTION1. Check that the thermostat does not have deformation, cracks or damage.2. Check that the thermostat valve closes completely at an ambient temperature.3. Immers ...
Installation
COOLING(H4DO) > ThermostatINSTALLATION1. ENGINE SIDE1. Install a gasket to thermostat.NOTE:Use a new gasket.2. Install the thermostat and thermostat cover.Tightening torque:6.4 N·m (0.7 kgf- ...
Other materials:
List of diagnostic trouble code (dtc) List
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > List of Diagnostic Trouble Code (DTC)LISTDTCItemContentReferenceU0073CONTROL MODULE COMMUNICATION BUS OFFDetected when CAN line abnormality is detected. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0073 CONTROL MODULE COMMUNICATION ...
Assembly
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Center DifferentialASSEMBLYInstall the ball bearings.CAUTION:Do not apply a load in excess of 10 kN (1 ton, 1.1 US ton, 1.0 Imp ton).NOTE:Use a new ball bearing.(A)Ball bearing ...
Dtc u0155 lost communication with instrument panel cluster (ipc) control module
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0155 LOST COMMUNICATION WITH INSTRUMENT PANEL CLUSTER (IPC) CONTROL MODULEDetected when CAN data from combination meter does not arrive.NOTE:Perform the diagnosis for LAN syst ...
