Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Removal

CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Control Valve Body

REMOVAL

CAUTION:

Directly after the vehicle has been running or the engine has been idling for a long time, the CVTF is hot. Be careful not to burn yourself.

Be careful not to spill CVTF on the exhaust pipe to prevent it from emitting smoke or causing a fire. If the CVTF adheres, wipe it off completely.

Always clean the engine compartment before removal.

NOTE:

The control valve body is replaced as an assembly only, because it is a non-disassembly part.

1. Disconnect the ground cable from battery. NOTE">

NOTE:

For model with battery sensor, disconnect the ground terminal from battery sensor.

2. Remove the clip (A) from the air intake boot.

3. Loosen the clamp (B) connecting the air intake boot and air cleaner case (rear).

4. Loosen the clamp (C) which connects the air intake boot and throttle body.

5. Remove the air intake boot from the throttle body, and move it to the left side wheel apron.

6. Disconnect the following connectors.

Transmission harness connectors

Inhibitor harness connector

Transmission radio ground terminal

(A)

Transmission harness connectors

(B)

Inhibitor harness connector

(C)

Transmission radio ground terminal

7. Remove the pitching stopper.

8. Remove the air breather hose from the pitching stopper bracket, and then remove the pitching stopper bracket and transmission radio ground cord.

9. Remove the transmission case cover.

10. Remove the transmission harness stay and ground terminal.

11. Remove the transmission harness connector from the harness stay.

12. Remove the throttle body, and move it aside so that it will not interfere with the removal of the control valve. Throttle Body > REMOVAL">

NOTE:

Do not remove the preheater hose.

13. Clean the transmission exterior.

14. Fix the ST with tape, and set the ST to the vehicle.

NOTE:

When replacing the control valve body, the sheet is included in the control valve body for repairs.

ST 18761AA010SHEET SPECIAL TOOL

15. Remove the valve cover and gasket.

16. Remove the transmission harness from the valve cover.

17. Remove the O-ring from the transmission harness.

18. Disconnect the harness connector from the control valve body.

19. Remove the control valve body.

20. Remove the O-ring from the transmission.

Inspection
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Control Valve BodyINSPECTION• Check each part for damage or dust.• Measure the resistance of each solenoid, sensor and ground wire.NOTE:Measu ...

Installation
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Control Valve BodyINSTALLATION1. Clean the mating surface of valve cover and transmission side.CAUTION:When cleaning the mating surface of the transmissi ...

Other materials:

Caution
DIFFERENTIALS > General DescriptionCAUTION• When performing any work, always wear work clothes, a work cap and protective shoes. Additionally, wear a helmet, protective goggles, etc. if necessary.• Remove contamination including dirt and corrosion before removal, installation, disasse ...

Dtc b1432 ambient temperature sensor circuit open (air-conditioner)
HVAC SYSTEM (AUTO A/C) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1432 AMBIENT TEMPERATURE SENSOR CIRCUIT OPEN (AIR-CONDITIONER)DTC detecting condition:Ambient sensor circuit is open.Trouble symptom:Ambient temperature is falsely recognized, and the compartment te ...

Installation
EXTERIOR/INTERIOR TRIM > Rear Gate GarnishINSTALLATIONCAUTION:Make sure that the harness grommet is securely installed.If not properly installed, this may cause leaks.Install each part in the reverse order of removal.Tightening torqueGarnish assembly - rear gate: 4.5 N·m (0.46 kgf-m, 3.3 f ...

© 2016-2022 Copyright www.sucross.com