Subaru Crosstrek Service Manual: Refrigerant leak check Inspection
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Refrigerant Leak Check
INSPECTION
1. Attach the manifold gauge set.
Preparation tool:
Manifold gauge set
(1) Check that all valves are fully closed.
(2) Install the low/high pressure hoses to the service ports on the low/high pressure sides of the vehicle respectively.
CAUTION:
Confirm that the connections are secure.
(3) Start the engine, operate the A/C system for approx. 10 minutes, and check that the high-pressure side indicates 0.69 MPa (7.0 kgf/cm2, 100 psi) or more.
2. Turn the ignition switch to OFF to start the leak test.
Preparation tool:
Electronic leak detector (leak tester)
Items | Condition | Corrective action |
Pipe | Check the connections of pipe and expansion valve. | Check the O-ring at connection and tightening torque. If necessary, replace each part. |
Check the connection between pressure switch or pressure sensor and high-pressure pipe. | Replace the pressure switch or pressure sensor. | |
Check the connection between pipe and condenser. | Check the O-ring at connection and tightening torque. If necessary, replace each part. | |
Condenser | Check the welded part of condenser and core. | Replace the condenser. |
Hose (high-pressure) | Check the connection between hose (high-pressure) and compressor. | Check the O-ring at connection and tightening torque. If necessary, replace each part. |
Check the connection between hose (high-pressure) and condenser. | Check the O-ring at connection and tightening torque. If necessary, replace each part. | |
Check the rubber part of the flexible hose and pipe seam. CAUTION: |
Carefully check the external surface of flexible hoses and pipes at approx. 25 mm (0.98 in) per second.
Replace the hose (high pressure).
Check the valve and cap in the service port.
Check the rubber seal of the valve and cap. If necessary, replace valve or cap.
Compressor
Check the compressor pulley and vicinity of shaft seal.
CAUTION:
Some shaft seals will show a slight amount of leakage, about 3 g (0.1 oz) per year. This is not a problem.
Replace the compressor.
Hose (low-pressure)
Check the connection between hose (low pressure) and expansion valve.
Check the O-ring at connection and tightening torque. If necessary, replace each part.
Check the connection between hose (low pressure) and compressor.
Check the O-ring at connection and tightening torque. If necessary, replace each part.
Check the rubber part of the flexible hose and pipe seam.
CAUTION:
Carefully check the external surface of flexible hoses and pipes at approx. 25 mm (0.98 in) per second.
Replace the hose (low pressure).
Check the valve and cap in the service port.
Check the rubber seal of the valve and cap. If necessary, replace valve or cap.
Evaporator
Remove the drain hose from the heater case, and check the end part for 10 seconds or more.
Replace the evaporator.
Check the air vent grille.
NOTE:
Turn the ignition switch to ON, and run the blower at high speed for approx. 1 minute. Stop the blower to check the air vent grille on the instrument panel. While moving the tester closer to the grille, run the blower for 1 or 2 seconds, then stop it. Check the grille at that position for at least 10 seconds.
Replace the evaporator.
Refrigerant charging procedure Procedure
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Refrigerant Charging ProcedurePROCEDURECAUTION:• While working, be sure to wear protective goggles and protective gloves.• Air in the cycle ca ...
Refrigerant recovery procedure Procedure
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Refrigerant Recovery ProcedurePROCEDURECAUTION:• During operation, be sure to wear protective goggles and protective gloves.• Connect the refr ...
Other materials:
Dtc p0108 manifold absolute pressure/barometric pressure sensor circuit high
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0108 MANIFOLD ABSOLUTE PRESSURE/BAROMETRIC PRESSURE SENSOR CIRCUIT HIGHDTC detecting condition:Immediately at fault recognitionCAUTION:After servicing or replacing faulty parts, perform Clear Memory Mode Cle ...
Removal
ENTERTAINMENT > AudioREMOVALCAUTION:Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">1. Disconnect the ground cable from battery and wait for at least 60 sec ...
Dtc u0155 lost communication with instrument panel cluster (ipc) control module
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0155 LOST COMMUNICATION WITH INSTRUMENT PANEL CLUSTER (IPC) CONTROL MODULENOTE:For the diagnostic procedure, refer to LAN section. Basic Diagnostic Procedure">1. OUTLINE OF DIAGNOSISDetect malfunctio ...
