Subaru Crosstrek Service Manual: Procedure
DIFFERENTIALS > Rear Differential Inspection Mode
PROCEDURE
CAUTION:
Do not turn the power of the Subaru Select Monitor OFF during work, and do not disconnect the data link connector.
1. Shift the select lever to “P” range.
2. Apply the parking brake.
3. Lift up the vehicle.
WARNING:
Lift up the vehicle until the tire bottom is 30 cm or more above the ground.
4. Connect the Subaru Select Monitor to data link connector.
5. Turn the ignition switch to ON.
6. Select «Diagnosis» in the «Start» screen of Subaru Select Monitor.
7. On «Vehicle selection» display, input the vehicle information and select «Confirmed».
8. On «Main Menu» display, select «Each System».
9. On «Select System» display, select «Transmission Control System».
10. On «Select Function» display, select «Work Support».
11. On «Work Support» display, select «Rear differential inspection mode».
12. Follow the messages displayed on the Subaru Select Monitor screen when working.
13. The results of the rear differential inspection mode are displayed on the Subaru Select Monitor screen.
• When ended normally: “The rear differential has been replaced normally.”
• When ended abnormally: “A rear differential abnormality has been detected. Reinspect the items at the time of rear differential installation.”
• When interrupted: “Inspection is stopped. Restart this inspection mode from the beginning.”
14. After the message “Inspection has been completed. Set the ignition switch to OFF.” appears, the rear differential inspection mode completes.
NOTE:
• When the rear differential inspection mode is completed properly, the following warning lights may illuminate. But this is not a malfunction. If warning light illuminates, clear the memory.
VDC/ABS, engine, power steering
• For detailed operation procedures, refer to “Application help”.
• If the rear differential inspection mode does not end normally, repeat the mode until it ends normally.
• When the inspection mode does not end normally, the AWD warning light will start blinking at 2 Hz.
• When the rear differential inspection mode ends abnormally, the front differential and rear differential may be different from the specifications for the vehicle.
• When the rear differential inspection mode is interrupted, the following reasons are possible.
Message | Main reasons for abnormal termination | Action to take |
• “Inspection is stopped.”
• “Inspection is stopped. Restart this inspection mode from the beginning.”
TCM has detected a failure.
Perform the diagnosis for TCM. Basic Diagnostic Procedure">
VDC has a failure.
Perform the diagnosis for VDC. Basic Diagnostic Procedure">
Brake is applied after start during automatic running.
—
Too delayed operation to the instructions displayed on the Subaru Select Monitor.
—
“TCM incompatible. Rear differential inspection mode is stopped.”
The model does not support the rear differential inspection mode.
Check the specifications.
The TCM has detected a fault. Inspect following the manual.
TCM has detected a failure.
Perform the diagnosis for TCM. Basic Diagnostic Procedure">
General description
DIFFERENTIALS > Rear Differential Inspection ModeGENERAL DESCRIPTIONCAUTION:Be sure to perform rear differential inspection mode.• Follow the messages displayed on the Subaru Select Monitor w ...
Other materials:
Removal
ENTERTAINMENT > Switches and HarnessREMOVAL1. SATELLITE SWITCH ASSEMBLYCAUTION:Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">1. Set the tire to the straig ...
Dtc b11f7 side impact deployment
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B11F7 SIDE IMPACT DEPLOYMENTDIAGNOSIS START CONDITION:Ignition voltage is 10 V to 16 V.DTC DETECTING CONDITION:This DTC is displayed when the side airbag module and curtain airbag module are deployed.Once this DTC is displayed, t ...
Removal
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Fuel InjectorREMOVAL1. Release the fuel pressure. Fuel > PROCEDURE">2. Disconnect the ground cable from battery.3. Open the fuel filler lid and remove the fuel filler cap.NOTE:This operation is required to release the inner pressure of the fuel ta ...
