Subaru Crosstrek Service Manual: Operation
VEHICLE DYNAMICS CONTROL (VDC) > ABS Sequence Control
OPERATION
1. While the ABS sequence control is being performed, the operation of the hydraulic unit can be checked using the brake tester or pressure gauge after the hydraulic unit solenoid valve operation.
2. ABS sequence control can be started by the Subaru Select Monitor.
1. ABS SEQUENCE CONTROL WITH SUBARU SELECT MONITOR
NOTE:
In the event of any trouble, the ABS sequence control will not operate.
1. Connect the Subaru Select Monitor.
NOTE:
For detailed operation procedures, refer to “Application help”.
(1) Turn the ignition switch to ON.
(2) On «Start» display, select «Diagnosis».
(3) On «Vehicle selection» display, input the target vehicle information and select «Confirmed».
(4) On «Main Menu» display, select «Each System».
(5) On «Select System» display, select «Brake Control System» and select «Enter».
(6) On «Select Function» display, select «Work Support».
(7) From the work support item list, select «ABS Sequence Control Mode».
2. Follow the procedures displayed in the Subaru Select Monitor to execute the following.
(1) When using a brake tester, depress the brake pedal with a force of 100 N (10.2 kgf, 22.5 lbf).
(2) When using a pressure gauge, press the brake pedal so that the pressure gauge indicates 3,500 kPa (36 kgf/cm2, 511 psi).
3. The brake system being operated is displayed on the Subaru Select Monitor.
2. CONDITIONS FOR ABS SEQUENCE CONTROL
NOTE:
The control operation starts at point A.
(1) | All wheel speed | (11) | RR compression valve | (20) | 0.6 seconds |
(2) | Ignition key | (12) | RL decompression valve | (21) | 0.4 seconds |
(3) | ABS warning light | (13) | RL compression valve | (22) | Point A |
(4) | Switch - stop light | (14) | Pump motor | (23) | Master cylinder pressure |
(5) | Valve relay | (15) | A few seconds | (24) | FL wheel cylinder pressure |
(6) | FL decompression valve | (16) | Light OFF | (25) | FR wheel cylinder pressure |
(7) | FL compression valve | (17) | Light ON | (26) | RR wheel cylinder pressure |
(8) | FR decompression valve | (18) | 1.0 second | (27) | RL wheel cylinder pressure |
(9) | FR compression valve | (19) | 1.4 seconds | ||
(10) | RR decompression valve |
Specification
VEHICLE DYNAMICS CONTROL (VDC) > ABS Sequence ControlSPECIFICATION1. CONDITIONS FOR COMPLETION OF ABS SEQUENCE CONTROLWhen the following conditions develop, the ABS sequence control stops and ABS o ...
Other materials:
Dtc c2511 torque sensor main
POWER ASSISTED SYSTEM (POWER STEERING) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C2511 TORQUE SENSOR MAINTrouble symptom:• The steering wheel operation feels heavy.• STEERING warning light illuminates.Wiring diagram:Electric power steering system Elec ...
Inspection
SECURITY AND LOCKS > Push Button Start SystemINSPECTION1. POWER SUPPLY SWITCH FUNCTION INSPECTION1. Check push button ignition switch function(1) Check the change control through push button ignition switch, brake pedal operation, and shift position.Shift lever positionBrake pedal operationPush b ...
Manual transmission
The manual transmission is a fully synchromeshed,
5-forward-speed and 1-reverse-
speed transmission.
The shift pattern is shown on the shift
lever knob. When shifting from 5th gear to
reverse gear, first return the shift lever to
the neutral position then shift into reverse
gear.
To ...
