Subaru Crosstrek Service Manual: Operation
INSTRUMENTATION/DRIVER INFO > Multi-function Display (MFD) System
OPERATION
1. DIAGNOSTIC MODE (HIGH GRADE TYPE ONLY)
The settings of the multi-function display can be changed by performing the following procedures to display the diagnostic mode. To show the demonstration display only, refer to “DEMONSTRATION DISPLAY”.
CAUTION:
• To avoid battery discharge, perform the procedure while charging the battery.
• While performing the work, close the front hood and all doors, and do not operate any electrical parts.
• Display can not be switched to diagnostic mode if the illumination control dial is set to the position for the dimming cancel function (maximum brightness).
1. Procedure
CAUTION:
Perform the steps described in (2) through (4) within 10 seconds.
(1) Turn the ignition switch to ON, and within 3 seconds, turn the lighting switch to Switch 1 (TAIL/PARKING) or Switch 2 (HEAD).
(2) While keeping the lighting switch to Switch 1 (TAIL/PARKING) or Switch 2 (HEAD) position, press the MFD (ENTER) switch three times.
(3) Turn the lighting switch to OFF, and press the MFD (ENTER) switch three times.
(4) Turn the lighting switch to Switch 1 (TAIL/PARKING) or Switch 2 (HEAD) position again, and press the MFD (ENTER) switch three times.
NOTE:
• Except for the demonstration display setting of the diagnostic mode, the display will terminate by turning the ignition switch to OFF (ACC OFF) or by selecting “Back” from the menu screen.
• The demonstration display setting of the diagnostic mode will terminate by starting the engine or removing the battery. Even if the ignition switch is turned to OFF (ACC OFF), then to ON again, the diagnostic mode will not terminate.
• To select other menus from the demonstration display setting, terminate the diagnostic mode by starting the engine or removing the battery, then access to the diagnostic mode again.
2. Display menu
Change the display and settings from each menu.
Menu | Item | Content |
Demonstration display setting | — | Shows demonstration display. |
Vehicle status confirmation | • CAN communication | Displays the connection status of input signals. |
• U-ART communication | ||
• Camera connection | ||
Customize | • Key operation sound | Select “ON” or “OFF”, then select “Set” to determine. |
• Correction of lifetime fuel economy value* | Adjust the fuel economy value within the range of −10 — +10 km/l, then determine the value with MFD (ENTER) switch. | |
Back | — | Finish the diagnostic mode. |
*: Correction of lifetime fuel economy value is used only when the multi-function display has been replaced. This function is provided as a compensation feature to bring the current lifetime fuel economy value to the one before the replacement of multi-function display.
2. DEMONSTRATION SCREEN DISPLAY (HIGH GRADE TYPE ONLY)
The demonstration screen can be displayed according to the following procedure.
CAUTION:
• Perform the steps while the ignition switch is OFF (ACC OFF).
• To avoid battery discharge, perform the operation under the following condition.
– Perform the operation while the battery is being charged.
– While performing the operation and displaying the demonstration mode, do not operate any electrical parts.
1. Procedure
CAUTION:
Perform the steps described in (2) through (5) within 10 seconds.
(1) Sit in the driver’s seat and close the door.
(2) Open the driver’s door, and within 5 seconds, press the MFD (ENTER) switch three times.
(3) Close the driver’s door, and press the MFD (ENTER) switch three times.
(4) Open the driver’s door, and press the MFD (ENTER) switch three times.
(5) Close the driver’s door, and press the MFD (ENTER) switch three times.
2. Go to “Demonstration screen display”.
NOTE:
The demonstration display will be cancelled in any of the following conditions.
• When 60 minutes elapsed since the demonstration mode started
• When the ignition switch is turned to ON
• When the MFD (ENTER) switch is turned to ON for two seconds
• When the battery voltage is low
3. ODO FUEL ECONOMY VALUE RESET (HIGH GRADE TYPE ONLY)
Follow the procedure below to initialize the ODO setting value.
1. Turn the ignition switch to ON, and press the MFD (ENTER) switch for two seconds.
2. Select “Factory delivery setting” from “Setting screen”.
3. Select “ODO setting reset” and determine with “Yes”.
4. The screen that indicates the completion of the setting is displayed for three seconds. This is the end of operation.
NOTE:
• The resetting operation is confirmed twice. Select confirmation according to the screen.
• The display will terminate by turning the ignition switch to OFF (ACC OFF) or by selecting “Back” from the menu screen.
Note
INSTRUMENTATION/DRIVER INFO > Multi-function Display (MFD) SystemNOTEFor procedure of each component in the Multi-Function Display (MFD) system, refer to the respective section.• Multi-functi ...
Relay and fuse
...
Other materials:
Ignition control system
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostics for Engine Starting FailureIGNITION CONTROL SYSTEMCAUTION:After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode">, and Inspection Mode Inspection Mode">.Wiring diagram:Engine electrical system Engine Elec ...
Reclining the seatback
Pull the reclining lever up and adjust the
seatback to the desired position. Then
release the lever and make sure the
seatback is securely locked into place.
The seatback placed in a reclined position
can spring back upward with force when
the lever is pulled. While operating the
lever ...
Dtc b280a vdc echo back disagreement
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B280A VDC ECHO BACK DISAGREEMENTDetected when error occurs in the VDC. (VDC brake control malfunction 1)When lost communication with vehicle dynamics control and vehicle dynamics control module abnormal or VDC ech ...
