Subaru Crosstrek Service Manual: Operation

1. SELF-DIAGNOSIS DISPLAY MODE

The self-diagnosis (checking of each meter, warning light, indicator light, illumination, LCD/TFT) of combination meter can be performed in the following procedure.

1. Procedure

CAUTION:

Perform the steps described in (1) through (4) within 10 seconds.

(1) Unfasten > fasten the driver’s seat belt within 3 seconds after the ignition switch is turned to ON.

(2) With the driver’s seat belt fastened, press the trip meter knob three times.

(3) Unfasten the driver’s seat belt, and then press the trip meter knob three times.

(4) Fasten the driver’s seat belt again, and then press the trip meter knob three times.

NOTE:

• When the self-diagnosis function operates, the warning light, indicator light, and LCD/TFT display checks are performed. After that, the buzzer will sound for 0.5 seconds every time the trip meter knob is pressed, and operation checks are performed in the order of meter indicator needle operation, meter indicator needle indication, and LCD/TFT. Turn the ignition switch to OFF to cancel the self-diagnosis function.

• When the engine starts during diagnosis, the self-diagnosis function is not cancelled, however, once the vehicle starts driving, the self-diagnosis function is deactivated automatically.

2. Go to “Check meter indicator operation”.

Check meter operation, warning light, indicator light, illumination and LCD/TFT.

NOTE:

• After “_S_1” is displayed on the LCD/TFT, the meter indicator operation check mode is initiated.

• Each of the meter indicator operation display and LCD/TFT display switches every 6 seconds.

*1: Warning lights and indicator lights controlled by the meter drive circuit are illuminated. General Description > SPECIFICATION">

*2: Warning lights and indicator lights controlled by other module are turned on/off according to the module control. General Description > SPECIFICATION">

*3: Engine coolant temperature warning light illuminates in red.

*4: Display for one second for each level.

3. Press the trip meter knob once.

4. Go to “Meter Indicator Needle Indication Check”.

Check meter operation, warning light, indicator light, and LCD/TFT.

NOTE:

• Meter indicator switches every 1.5 seconds for each indication.

• ILL indication illuminates at the same brightness as when entering “Meter Indicator Needle Indication Check”.

• During operation, “_S_2” is displayed on the LCD/TFT trip display.

*1: Warning lights and indicator lights controlled by the meter drive circuit go off. General Description > SPECIFICATION">

*2: Warning lights and indicator lights controlled by other module are turned on/off according to the module control. General Description > SPECIFICATION">

*3: Engine coolant temperature indicator light illuminates in blue.

5. Press the trip meter knob once.

6. Go to “Check LCD/TFT display”.

Check the LCD/TFT display.

NOTE:

• After “_S_3” is displayed on the LCD/TFT, the LCD/TFT display check mode is initiated.

• LCD/TFT display switches every 1 second.

• Warning lights and indicator lights controlled by the meter drive circuit go off. General Description > SPECIFICATION">

• Warning lights and indicator lights controlled by other module are turned on/off according to the module control. General Description > SPECIFICATION">

• The meter indication remains at the same level as “Meter Indicator Needle Indication Check”.

• ILL indication illuminates at ILL6 level (max. brightness).

• After No. 14 is displayed in the illumination order, display is repeated from No. 1 again. (models with normal meters)

• After No. 8 is displayed in the illumination order, display is repeated from No. 1 again. (Model with color TFT meter)

• The version display contents of the illumination order No. 1 varies depending on the vehicle. (Model with color TFT meter)

Model with normal meter

• Perform the steps while the ignition switch is OFF (ACC OFF) and the odo/trip meter is not displayed.

• To avoid battery discharge, perform the operation under the following condition.

– Perform the operation while the battery is being charged.

– While performing the operation and displaying the demonstration mode, close all doors and do not operate any electrical parts.

1. Procedure

CAUTION:

Perform the steps described in (1) through (4) within 10 seconds.

(1) Press the trip meter knob twice.

NOTE:

When the trip meter knob is pressed once, the odo/trip meter is displayed.

(2) Press the MID (i/SET) switch three times within three seconds after the operation (1) above is performed.

(3) Press the trip meter knob once, and press the MID (i/SET) switch three times.

(4) Press the trip meter knob once, and press the MID (i/SET) switch three times.

2. The “demonstration mode” is initiated.

CAUTION:

If the procedure is not performed properly, stop the operation and wait until the odo/trip meter display disappears (for approx. 10 seconds), and then perform the procedure from (1) to (4) again after confirming that the display disappeared.

The demonstration mode will be cancelled in the following condition.

When resuming the operation after cancellation, the demonstration mode is displayed, however, for the model with keyless access with push button start, the resuming can only be accepted after approx. 1 minute.

• At the completion of the “goodbye screen” display that is shown 60 minutes after the demonstration mode is initiated

• When the ignition switch is turned to ON

• When the MID (i/SET) switch is turned to ON for two seconds

• When the battery voltage is low

• When the push button ignition switch is pressed with the access key out of the passenger room (model with keyless access with push button start)

• When any request switch is pressed with the access key in the passenger room (model with keyless access with push button start)

Note

General description

Other materials:

General diagnostic table Inspection
ENGINE (DIAGNOSTICS)(H4DO) > General Diagnostic TableINSPECTION1. ENGINENOTE:Malfunction of parts other than those listed is also possible. Engine Trouble in General">SymptomsFaulty parts1. Engine stalls during idling.1) Manifold absolute pressure sensor2) Mass air flow and intake air te ...

Inspection
TIRE PRESSURE MONITORING SYSTEM (DIAGNOSTICS) > Tire Pressure Warning Light / Trouble Indicator Light Illumination PatternINSPECTION(1)Ignition switch(8)Tire inflation pressure warning light (pressure condition)(15)Light OFF(2)OFF(9)Light OFF(16)Blink(3)ON(10)Light ON(17)1 second(4)Start(11)Syste ...

Dtc b28af stereo camera adjustment incomplete
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B28AF STEREO CAMERA ADJUSTMENT INCOMPLETEDetected when adjustment or inspection of stereo camera has not been completed normally.DTC DETECTING CONDITION:• Operation is aborted during adjustment or inspection ...