Subaru Crosstrek Service Manual: List of diagnostic trouble code (dtc) List
BODY CONTROL SYSTEM (DIAGNOSTICS) > List of Diagnostic Trouble Code (DTC)
LIST
DTC | Item | Content of diagnosis | Note |
B1010 | BODY CONTROL SYSTEM (BIU) MALFUNCTION | Body integrated unit internal error | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1010 BODY CONTROL SYSTEM (BIU) MALFUNCTION"> |
B1011 | BATTERY CONTROL POWER SUPPLY | Voltage malfunction caused by poor contact of battery power supply control circuits | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1011 BATTERY CONTROL POWER SUPPLY"> |
B1012 | BATTERY BACKUP POWER SUPPLY | Voltage malfunction caused by poor contact of battery power supply backup circuits | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1012 BATTERY BACKUP POWER SUPPLY"> |
B1013 | IGNITION POWER | Voltage malfunction caused by poor contact of IGN power supply circuits | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1013 IGNITION POWER"> |
B1014 | ACC POWER | Voltage malfunction caused by poor contact of ACC power supply circuits | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1014 ACC POWER"> |
B1015 | KEY INTERLOCK CIRCUIT | GND-output short of key interlock circuit | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT"> |
B1016 | SHIFT LOCK CIRCUIT | Voltage malfunction caused by poor contact of shift lock circuits | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1016 SHIFT LOCK CIRCUIT"> |
B1401 | METER COLLATION | Malfunction related immobilizer | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1401 METER COLLATION"> |
B1402 | IMMOBILIZER KEY COLLATION | Malfunction related immobilizer | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1402 IMMOBILIZER KEY COLLATION"> |
B1405 | SCU COLLATION | Malfunction related immobilizer | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1405 SCU COLLATION"> |
B1406 | SCU_EEPROM | Malfunction of security control module | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1406 SCU_EEPROM"> |
B1407 | MET COMMUNICATION | Communication failure between body integrated unit and combination meter | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1407 MET COMMUNICATION"> |
B1408 | METER NON-VOLATILE MEMORY | Combination meter malfunction | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1408 METER NON-VOLATILE MEMORY"> |
B1409 | SCU COMMUNICATION | Communication failure between body integrated unit and security control module | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1409 SCU COMMUNICATION"> |
B1410 | TRANSPONDER COMMUNICATION | Communication failure between key and body integrated unit | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1410 TRANSPONDER COMMUNICATION"> |
B1411 | IMMOBILIZER ANTENNA | Faulty antenna | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1411 IMMOBILIZER ANTENNA"> |
U1500 | KEYLESS UART COM. MALFUNCTION | Open or short circuit in keyless UART circuit | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1500 KEYLESS UART COM. MALFUNCTION"> |
General diagnostic table Inspection
BODY CONTROL SYSTEM (DIAGNOSTICS) > General Diagnostic TableINSPECTIONRead the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)"> Or check the following data under the c ...
Read diagnostic trouble code (dtc) Operation
BODY CONTROL SYSTEM (DIAGNOSTICS) > Read Diagnostic Trouble Code (DTC)OPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle informatio ...
Other materials:
Removal
CONTROL SYSTEMS > AT Shift Lock Solenoid and “P” Range SwitchREMOVAL1. SOLENOID UNIT1. Remove the AT select lever. Select Lever > REMOVAL">2. Remove the spacer and gasket. Select Lever > DISASSEMBLY">3. Using a flat tip screwdriver with a thin tip, remove the h ...
Removal
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Transfer Case and Extension Case AssemblyREMOVAL1. Remove the manual transmission assembly from the vehicle. Manual Transmission Assembly > REMOVAL">2. Remove the back-up light switch and the neutral position switch. Switches and Harness &g ...
Dtc b16f1 passenger s seat belt warning failure
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B16F1 PASSENGER’S SEAT BELT WARNING FAILUREDiagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting condition:• Airbag control module is faulty.• Meter is faulty.• Harness circuits between ...
