LAN SYSTEM (DIAGNOSTICS) > CAN Communication Circuit Check
LIST
Resistance value between CAN Hi and Lo | Contents of inspection | Remarks |
Ground short inspection | CAN Communication Circuit Check > INSPECTION"> | Shorted to ground in the communication circuit or control module. |
Battery short inspection | CAN Communication Circuit Check > INSPECTION"> | Shorted to battery power supply in the communication circuit or control module. |
53 — 61 ? | CAN Communication Circuit Check > INSPECTION"> | Combined resistance of end resistance does not have malfunction; short to ground or +B short of the CAN communication circuit is possible, however. |
52 ? or less | CAN Communication Circuit Check > INSPECTION"> | Resistance is lower than combined resistance of end resistance. Short to CAN Hi and CAN Lo on the CAN communication circuit is possible. |
62 ? or more | CAN Communication Circuit Check > INSPECTION"> | Resistance is higher than combined resistance of end resistance. Open circuit of CAN communication circuit is possible. |
Related lines 53 — 61 ? (TCM) | CAN Communication Circuit Check > INSPECTION"> | No TCM data is received. Perform inspection when faulty is detected. |
Related lines 53 — 61 ? (steering angle sensor) | CAN Communication Circuit Check > INSPECTION"> | No steering angle sensor data is received. Perform inspection when faulty is detected. |
Related lines 53 — 61 ? (A/C control panel) | CAN Communication Circuit Check > INSPECTION"> | No A/C data is received. Perform inspection when faulty is detected. |
Related lines 53 — 61 ? (power steering) | CAN Communication Circuit Check > INSPECTION"> | No power steering data is received. Perform inspection when faulty is detected. |
Related lines 53 — 61 ? (combination meter) | CAN Communication Circuit Check > INSPECTION"> | No meter data is received. Perform inspection when faulty is detected. |
Related lines 53 — 61 ? (MFD) | CAN Communication Circuit Check > INSPECTION"> | No MFD data is received. Perform inspection when faulty is detected. |
Related lines 53 — 61 ? (airbags) | CAN Communication Circuit Check > INSPECTION"> | No airbag data is received. Perform inspection when faulty is detected. |
Related lines 53 — 61 ? (headlight beam leveler) | CAN Communication Circuit Check > INSPECTION"> | No headlight beam leveler data is received. Perform inspection when faulty is detected. |
Related lines 53 — 61 ? (remote engine starter) | CAN Communication Circuit Check > INSPECTION"> | Perform inspection when the remote engine starter does not operate, while the mobile key side operates normally. |
Related lines 53 — 61 ? (keyless access system) | CAN Communication Circuit Check > INSPECTION"> | No keyless access CM data is received. Perform inspection when faulty is detected. |
Related lines 53 — 61 ? (stereo camera) | CAN Communication Circuit Check > INSPECTION"> | No stereo camera data is received. Perform inspection when faulty is detected. |
Related lines 53 — 61 ? (telematics) | CAN Communication Circuit Check > INSPECTION"> | No telematics data is received. Perform inspection when faulty is detected. |
Related lines 53 — 61 ? (radar sensor) | CAN Communication Circuit Check > INSPECTION"> | No radar sensor data is received. Perform inspection when faulty is detected. |
Removal
ENTERTAINMENT > AudioREMOVALCAUTION:Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">1. Disconnect the ground cable from battery and wait for at least 60 sec ...
Dtc c2021 tire 1 air pressure low (normal mode)
TIRE PRESSURE MONITORING SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C2021 TIRE 1 AIR PRESSURE LOW (NORMAL MODE)NOTE:Refer to DTC C2024 for diagnostic procedure. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2024 TIRE 4 AIR PRESSURE LOW ( ...
Dtc u0423 invalid data received from instrument panel cluster control module
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0423 INVALID DATA RECEIVED FROM INSTRUMENT PANEL CLUSTER CONTROL MODULEReceived error data from combination meter.NOTE:Perform the diagnosis for LAN system. Basic Diagnostic ...