Subaru Crosstrek manuals

Subaru Crosstrek Owners Manual: Installing forward facing child restraint

WARNING

Before installing a child restraint system, be sure to confirm that the seatback is securely locked into place. Otherwise, in an accident, serious injury or death could result.

1. Shake the seatback slightly to confirm that it is securely locked into place.

2. Prepare the rear seat head restraint where a child restraint system is intended to be installed in the following way.

3. Place the child restraint system in the rear seating position.

WARNING

When you intend to install a child restraint system on the rear center seating position, if the child restraint system does not fit snugly against the contours of the rear center seat cushion, install the child restraint system on the window-side seating position to be safe. For details, refer to "Where to place a child restraint system" 1-25.

Installing forward facing child restraint

4. Run the lap and shoulder belt through or around the child restraint system following the instructions provided by its manufacturer.

5. Insert the tongue plate into the buckle until you hear a click.

Installing forward facing child restraint

6. Take up the slack in the lap belt.

7. Pull out the seatbelt fully from the retractor to change the retractor over from the Emergency Locking Retractor (ELR) to the Automatic Locking Retractor (ALR) function. Then, allow the belt to rewind into the retractor. As the belt is rewinding, clicks will be heard which indicate the retractor functions as ALR.

Installing forward facing child restraint

8. Before having a child sit in the child restraint system, try to move it back and forth and right and left to check if it is firmly secured. Sometimes a child restraint system can be more firmly secured by pushing it down into the seat cushion and then tightening the seatbelt.

9. Pull at the shoulder portion of the belt to confirm that it cannot be pulled out (ALR properly functioning).

Installing forward facing child restraint

10. Latch the top tether hook onto the tether anchorage that is located behind the rear seat and tighten the top tether firmly. For additional instructions, refer to "Top tether anchorages" 1-36.

Installing forward facing child restraint

11. To remove the child restraint system, press the release button on the seatbelt buckle and allow the belt to retract completely. The belt will return to the ELR mode.

If you have installed a child restraint system for the rear center seating position, when you remove the child restraint system, the seatbelt may not be restored to the ELR mode even if the seatbelt is retracted. In this case, lower the head restraint to the retracted position to allow the seatbelt to retract moreover. The seatbelt will return to the ELR mode.

Remember that the head restraint is not intended to be used at the lowest position (retracted position). Therefore, when the rear center seat is occupied (including when a child restraint system is installed) next time, be sure to raise the head restraint to the extended position.

NOTE

When the child restraint system is no longer in use, remove it and restore the ELR function of the retractor. That function is restored by allowing the seatbelt to retract fully.

Installing a rearward facing child restraint
1. Place the child restraint system in the rear seating position. 2. Run the lap and shoulder belt through or around the child restraint system following the instructions provided by its ma ...

Installing a booster seat
WARNING Child restraint systems and seatbelts can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check the child restraint system before ...

Other materials:

Dtc c0045 tcm malfunction
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C0045 TCM MALFUNCTIONDTC detecting condition:Defective TCMTrouble symptom:• ABS does not operate.• VDC does not operate.• EyeSight does not operate.STEPCHECKYESNO1.CHECK CVT ...

Installation
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Transfer Drive GearINSTALLATION1. Install the transfer drive gear.Tightening torque:26 N·m (2.7 kgf-m, 19.2 ft-lb)2. Select the adjusting washer. Transfer Case and Extension Case Assembly > INSTALLATION">3. Install the transfer driven ...

Service diagnostics mode Operation
ENTERTAINMENT > Service Diagnostics ModeOPERATIONNOTE:Installed only to model with 7 inch display.1. PROCEDURE TO SWITCH TO SERVICE DIAGNOSTICS MODE1. Turn the ignition switch to ACC.2. After turning the ignition switch to ACC and wait for 20 seconds or more, press the button (b) five times with ...

© 2016-2024 Copyright www.sucross.com