Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Installation

WIPER AND WASHER SYSTEMS > Front Wiper Arm

INSTALLATION

1. MODELS WITHOUT EyeSight

1. Install the arm assembly - windshield wiper.

(1) Assemble the arm assembly - windshield wiper so that the blade assembly - windshield wiper is aligned to the ceramic print point mark of the windshield glass.

(2) Tighten the arm assembly - windshield wiper to specified torque and install the cap.

Tightening torque:

26 N·m (2.65 kgf-m, 19.2 ft-lb)

2. Operate the windshield wiper to check that the stop position is aligned with the point mark.

If it is not aligned with the point mark, perform the removal and installation of the windshield wiper over again. Front Wiper Arm > REMOVAL">

2. MODELS WITH EyeSight

CAUTION:

Install firmly so that the hose is not bent, compressed or flattened.

1. When the hose is removed from the joint ­ washer hose, refer to “Installation” of “Front washer nozzle & hose”. Front Washer Nozzle and Hose > INSTALLATION">

2. Install the arm assembly - windshield wiper.

(1) Align the alignment mark (a), and install the hose to the arm assembly - windshield wiper assistor.

(2) Assemble the arm assembly - windshield wiper so that the blade assembly - windshield wiper is aligned to the ceramic print point mark of the windshield glass.

(3) Tighten the arm assembly - windshield wiper to specified torque and install the cap.

Tightening torque:

26 N·m (2.65 kgf-m, 19.2 ft-lb)

3. Operate the windshield wiper to check that the stop position is aligned with the point mark.

If it is not aligned with the point mark, perform the removal and installation of the windshield wiper over again. Front Wiper Arm > REMOVAL">

4. Make sure that there is a gap of 1 mm (0.04 in) or more between the hose and the cover ­ joint and between the hose and the joint ­ washer hose during windshield wiper operation.

(A)

Gap between hose and cover ­ joint outer side

(C)

Gap between hose and cover ­ joint inner side

(D)

Gap between hose and cover ­ joint lower side

(B)

Gap between hose and cover ­ joint upper side

Removal
WIPER AND WASHER SYSTEMS > Front Wiper ArmREMOVAL1. MODELS WITHOUT EyeSight1. Remove the cover - windshield wiper arm.2. Remove the nuts, and remove the arm assembly - windshield wiper.2. MODELS WI ...

Front wiper motor and link
...

Other materials:

Clear memory mode Operation
ENGINE (DIAGNOSTICS)(H4DO) > Clear Memory ModeOPERATION1. SUBARU SELECT MONITORNOTE:• Initial diagnosis of electronic throttle control is performed after memory clearance. Wait for 10 seconds or more after turning the ignition switch to ON, and then start the engine.• For detailed ope ...

Steering angle sensor Replacement
VEHICLE DYNAMICS CONTROL (VDC) > Steering Angle SensorREPLACEMENTCAUTION:• If the steering wheel and steering angle sensor are removed, perform the following VDC setting mode.– Model without EyeSight: VDC sensor midpoint setting mode VDC Control Module and Hydraulic Control Unit (VDCCM& ...

Caution
IGNITION(H4DO) > General DescriptionCAUTION• Prior to starting work, pay special attention to the following:1. Always wear work clothes, a work cap, and protective shoes. Additionally, wear a helmet, protective goggles, etc. if necessary.2. Protect the vehicle using a seat cover, fender cov ...

© 2016-2024 Copyright www.sucross.com