Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Installation

SEAT BELT SYSTEM > Front Seat Belt

INSTALLATION

1. SEAT BELT OUTER - FRONT

CAUTION:

The parts of the driver and passenger sides are not the same. Before installation, make sure that the correct part is used.

During installation, make sure that the seat belts are not twisted.

After installation, make sure that the seat belt can be pulled out and retracted smoothly.

Make sure that the seat belt harness is not caught anywhere. Wrong harness rooting may cause the harness short from pinch.

Do not reuse the upper clips of the trim panel - center pillar UPR. Once the clip is removed, its holding force is reduced. Be sure to replace it with a new clip.

1. Before installation, perform a unit inspection of retractor. Front Seat Belt > INSPECTION">

2. Install the adjuster assembly - seat belt and the seat belt outer - front.

Tightening torque:

Front seat belt: General Description > COMPONENT">

3. Install the remaining parts in the reverse order of removal.

Tightening torque

Trim panel - center pillar UPR: 7.5 N·m (0.76 kgf-m, 5.5 ft-lb)

NOTE:

Assemble the trim panel - center pillar LWR to the trim panel - center pillar UPR securely.

4. After installation, check the following points.

The seat belt is not twisted.

The seat belt can be pulled out and retracted smoothly.

The adjuster assembly - seat belt can be moved smoothly.

Check that the airbag warning light lights up for approximately 6 seconds and then turns off when connecting the battery ground cable and turning the ignition switch to ON.

2. SEAT BELT INNER - FRONT

CAUTION:

Before installation, make sure that the correct part is used.

During installation, make sure that the seat belts are not twisted.

Check that there is no pinching of the seat belt harness. Wrong harness rooting may cause the harness short from pinch.

Do not forget the wave washer, when installing front seat inner belt assembly.

1. Install the seat belt inner - front.

Tightening torque:

Front seat belt: General Description > COMPONENT">

2. Locate the seat belt harness and retain it with a harness clip.

3. Install the seat assembly to the body. Front Seat > INSTALLATION">

4. Check that no harness is caught by sliding the seat back and forth.

5. Connect the battery ground terminal. NOTE">

3. ADJUSTABLE ANCHOR ASSY

Referring to the installation procedure for seat belt outer - front, install the parts in the reverse order of removal.

Tightening torque:

Front seat belt: General Description > COMPONENT">

Trim panel - center pillar UPR: 7.5 N·m (0.76 kgf-m, 5.5 ft-lb)

Removal
SEAT BELT SYSTEM > Front Seat BeltREMOVAL1. SEAT BELT OUTER - FRONTCAUTION:• Before handling the airbag system components, refer to “CAUTION” of “General Description” ...

General description
...

Other materials:

Dtc b1620 side airbag sensor rh failure
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B1620 SIDE AIRBAG SENSOR RH FAILUREDIAGNOSIS START CONDITION:Ignition voltage is 10 V to 16 V.DTC DETECTING CONDITION:Side airbag sensor (RH) is faulty.When DTC B1620 is displayed, the circuit within the side airbag sensor (RH) i ...

Trailer brakes
WARNING Adequate size trailer brakes are required when the trailer and its cargo exceed 1,000 lbs (453 kg) total weight. Do not directly connect your trailer's hydraulic brake system to the hydraulic brake system in your vehicle. Direct connection would cause the vehicle's brake ...

List
EyeSight (DIAGNOSTICS) > Freeze Frame Data DisplayLIST• List of freeze frame dataDisplayContentUnitECU Power Supply Voltage (IG)Display of input voltage of stereo cameraVEngine SpeedEngine speedrpmAccel opening angleAcceleration opening angle signal%Brake Fluid Target PressureTarget value o ...

© 2016-2024 Copyright www.sucross.com