Subaru Crosstrek Service Manual: Installation
REAR SUSPENSION > Rear Sub Frame
INSTALLATION
CAUTION:
• Be sure to use a new self-locking nut.
• Always tighten the bushing in the state where the vehicle is at curb weight and the wheels are in full contact with the ground.
• Install so that the front end of the under cover (b) comes inside the bumper face - front (a), and the front end of the mud guard (c) comes outside the bumper face - front (a).
1. Check the removed parts for wear, damage and crack, and repair or replace them if faulty.
2. Install each part in the reverse order of removal.
Tightening torque:
• Rear suspension parts: General Description > COMPONENT">
• Fuel tank protector: Fuel Tank Protector > REMOVAL">
• Rear disc brake parts: General Description > COMPONENT">
• Parking brake parts: General Description > COMPONENT">
• Exhaust pipe parts: General Description > COMPONENT">
• Propeller shaft parts: Propeller Shaft > INSTALLATION">
3. Install the under cover - front.
Tightening torque:
18 N·m (1.84 kgf-m, 13.3 ft-lb)
4. Bleed air from brake system. Air Bleeding > PROCEDURE">
5. Install the rear wheels.
Tightening torque:
Except for C4 model: 120 N·m (12.24 kgf-m, 88.5 ft-lb)
C4 model: 100 N·m (10.20 kgf-m, 73.8 ft-lb)
6. Inspect the wheel alignment and adjust if necessary.
• Inspection: Wheel Alignment > INSPECTION">
• Adjustment: Wheel Alignment > ADJUSTMENT">
CAUTION:
When the wheel alignment has been adjusted, perform the following VDC setting mode.
– Model without EyeSight: VDC sensor midpoint setting mode VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT">
– Model with EyeSight: Neutral of Steering Angle Sensor & Lateral G Sensor 0 point setting VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT">
– Model with EyeSight: Longitudinal G sensor & lateral G sensor 0 point setting VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT">
7. Connect the battery ground terminal.
8. Perform reinitialization of the auto headlight beam leveler system. (Model with auto headlight beam leveler) Auto Headlight Beam Leveler System > PROCEDURE">
Removal
REAR SUSPENSION > Rear Sub FrameREMOVAL1. Disconnect the ground cable from battery. NOTE">2. Lift up the vehicle, and then remove the rear wheels.3. Remove the bolts and clips, and remove ...
Other materials:
Dtc b1570 antenna
IMMOBILIZER (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1570 ANTENNADTC detecting condition:Faulty antennaCAUTION:When the body integrated unit is replaced, registration of the immobilizer system is required. For details, refer to the “REGISTRATION MANUAL FOR ...
Installation
DRIVE SHAFT SYSTEM > Rear Hub Unit BearingINSTALLATION1. Place the rear brake back plate between the rear axle housing and the rear hub unit bearing, and tighten the bolt.CAUTION:• Be careful not to damage the magnetic encoder.• Do not get closer the tool which charged magnetism to ma ...
Tire pressure warning light is 25 times blinking and turn on
TIRE PRESSURE MONITORING SYSTEM (DIAGNOSTICS) > Tire Pressure Warning Light / Trouble Indicator Light Illumination PatternTIRE PRESSURE WARNING LIGHT IS 25 TIMES BLINKING AND TURN ONDetecting condition:• Defective TPMS & keyless entry CM or TPMS CM• Defective harness• Transm ...
