Subaru Crosstrek Service Manual: Installation

1. Insert the steering gearbox assembly into crossmember, being careful not to damage the boot of the steering gearbox assembly.

2. Install the steering gearbox assembly to the crossmember by tightening the bolts through the stiffener (a) to the specified torque.

Tightening torque:

60 N·m (6.12 kgf-m, 44.3 ft-lb)

3. Install the universal joint assembly - steering. Universal Joint > INSTALLATION">

CAUTION:

Tighten the bolts of the universal joint assembly - steering in the order of steering gearbox side and column shaft side.

4. Install the support plate - front crossmember (a).

Tightening torque:

Support plate - front crossmember: 60 N·m (6.12 kgf-m, 44.3 ft-lb)

Front support: 100 N·m (10.20 kgf-m, 73.8 ft-lb)

5. Connect the tie-rod ends and knuckle arm.

(1) Connect the tie-rod end (a) to the housing assembly - front axle.

(2) Tighten the castle nuts (b) to the specified torque.

CAUTION:

During connection, do not hit the cap at bottom of tie-rod end with a hammer.

Castle nut tightening torque:

27 N·m (2.75 kgf-m, 19.9 ft-lb)

(3) Tighten within the range of 60° so that the cotter pin hole and cutout portion of the castle nut (b) are aligned.

(4) Insert the cotter pin (c), and bend the tip of the pin to fix it.

6. Install the front crossmember - support.

Tightening torque:

60 N·m (6.12 kgf-m, 44.3 ft-lb)

7. Install the front exhaust pipe assembly. Front Exhaust Pipe > INSTALLATION">

8. Install the under cover - front. Front Under Cover > INSTALLATION">

9. Install the front wheels.

10. Lower the vehicle.

11. Tighten the wheel nuts to the specified torque.

Tightening torque:

Except for C4 model: 120 N·m (12.24 kgf-m, 88.5 ft-lb)

C4 model: 100 N·m (10.20 kgf-m, 73.8 ft-lb)

12. Connect the power steering control module harness connector.

13. Connect the battery ground terminal.

CAUTION:

When the wheel alignment has been adjusted, perform the adjustment of the steering angle sensor.

– Model without EyeSight: VDC sensor midpoint setting mode VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT">

– Model with EyeSight: Neutral of Steering Angle Sensor & Lateral G Sensor 0 point setting VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT">

– Model with EyeSight: Longitudinal G sensor & lateral G sensor 0 point setting VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT">

14. After adjusting toe-in and steering angle, tighten the lock nut on tie-rod end.

Tightening torque:

85 N·m (8.67 kgf-m, 62.7 ft-lb)

When adjusting toe-in, hold the boot - steering gearbox as shown to prevent it from being rotated or twisted. If it becomes twisted, straighten it.

Inspection

General description

Other materials:

Installation
ENTERTAINMENT > AudioINSTALLATIONCAUTION:• After installing the center grille assembly, check that the air vent grille of the center grille assembly is inserted correctly into the air vent duct.• Before handling the airbag system components, refer to “CAUTION” of “Ge ...

Dtc u0131 lost communication with power steering control module
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0131 LOST COMMUNICATION WITH POWER STEERING CONTROL MODULEDetected when CAN data is not received from electric power steering CM.NOTE:Perform the diagnosis for LAN system. Basic Diagnostic Pro ...

Using the phone switch/microphone
Steering switch By pressing the steering switch, a call can be received or ended without taking your hands off the steering wheel. Volume control switch Off hook switch On hook switch Microphone The microphone is used when talking on the phone. Type A Type B How ...