Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Installation

MECHANICAL(H4DO) > Crank Pulley

INSTALLATION

1. Degrease the press-fit section for the chain cover front oil seal, and install the front oil seal to the chain cover using ST.

CAUTION:

Do not apply fluid such as engine oil to the front oil seal and the chain cover; otherwise engine oil leakage may occur.

NOTE:

Use a new front oil seal.

When tapping the front oil seal in, protect the radiator fin with cardboards etc. so as not to damage the radiator fin by the plastic hammer.

ST 41399FG020SPECIAL TOOL B

Front oil seal press-fit position:

1+0 −1 mm (0.0039+0 −0.0039 in) position from chain cover end face

(A)

Chain cover

(B)

Oil seal

(C)

Front oil seal press-fit position (1+0 −1 mm (0.0039+0 −0.0039 in) position from chain cover end face)

2. Clean the crankshaft thread using compressed air.

3. Apply engine oil to the crank pulley bolt seat and thread.

4. Install the crank pulley.

(1) Set the crank pulley to the chain cover.

NOTE:

Use new O-rings.

Install the crank pulley by aligning the crank pulley knock hole (A) and crank pulley boss knock pin (B).

(2) Use the ST to lock the crank pulley, and temporarily tighten the crank pulley bolt.

NOTE:

To prevent damaging ST1, attach the ST2 onto the ST1 as shown.

ST1 18355AA000PULLEY WRENCH
ST2 18334AA000PULLEY WRENCH PIN SET

ST1 18355AA000PULLEY WRENCH
ST2 18334AA000PULLEY WRENCH PIN SET

Tightening torque:

60 N·m (6.1 kgf-m, 44.3 ft-lb)

(3) Draw reference lines (A) and (B) using a marker to set the socket to the crank pulley bolt as shown in the figure.

(a)

When using 6-point socket

(b)

When using 12-point socket

(4) Draw reference lines (A) and (B) on the crank pulley bolt using a marker as shown in the figure.

(5) Draw end line (C) on crank pulley using a marker at the same position as reference line (B) drawn on the crank pulley bolt in step (3).

(6) Use the ST to lock the crank pulley, and tighten the crank pulley bolt to the angle where reference line (A) and end line (C) are aligned.

NOTE:

It should be approx. 60° when reference line (A) and end line (C) are aligned.

ST1 18355AA000PULLEY WRENCH
ST2 18334AA000PULLEY WRENCH PIN SET

Tightening angle:

60°±5°

5. Install the V-belts. V-belt > INSTALLATION">

6. When working on the vehicle

NOTE:

When working on the vehicle, perform the following steps also.

(1) Install the radiator main fan & fan motor assembly and radiator sub fan & fan motor assembly. Radiator Main Fan and Fan Motor > INSTALLATION"> Radiator Sub Fan and Fan Motor > INSTALLATION">

Removal
MECHANICAL(H4DO) > Crank PulleyREMOVALNOTE:When replacing a single part, perform the work with the engine assembly installed to body.1. When working on the vehicleNOTE:When working on the vehicle, ...

Crank sprocket
...

Other materials:

Installation
BRAKE > Rear Disc RotorINSTALLATIONNOTE:Before installation, remove mud and foreign matter from the caliper body assembly.1. Before installation, check the rear disc rotor. Rear Disc Rotor > INSPECTION">2. Install each part in the reverse order of removal.NOTE:When installing the rear ...

Dtc b1507 external air temperature open/short-circuit detection
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1507 EXTERNAL AIR TEMPERATURE OPEN/SHORT-CIRCUIT DETECTIONDTC detecting condition:Open or short circuit in ambient sensorTrouble symptom:• Defective ambient temperature display• Def ...

Installation
MECHANICAL(H4DO) > CamshaftINSTALLATION1. CAMSHAFT RHThe camshaft RH and cam carrier are designed as installing as a unit. Refer to “Cam Carrier” for installation procedures of camshaft RH. Cam Carrier > ASSEMBLY"> Cam Carrier > INSTALLATION">2. CAMSHAFT LHThe ...

© 2016-2024 Copyright www.sucross.com