Subaru Crosstrek Service Manual: Installation

1. Clean the mating surfaces of the transmission case, transfer case and extension case.

2. Apply a coat of grease to the taper roller bearing (transfer case side) of transfer driven gear and the roller rolling surface of the taper roller bearing (extension case side).

Grease:

NICHIMOLY N-130 or equivalent

3. Install the center differential and the transfer driven gear.

4. Install the taper roller bearing (extension case side) outer race to the transfer driven gear.

5. While pressing the taper roller bearing (extension case side) outer race horizontally, rotate the transfer driven gear for ten turns.

6. Measure the height “W” between transfer case and taper roller bearing (transfer case side) on the transfer driven gear.

7. Measure the depth “X” of taper roller bearing insertion part of the extension case.

NOTE:

Measure while the taper roller bearing (extension case side) outer race, dish plate and adjusting washer are removed.

8. Calculate the adjusting washer thickness “t” using the following calculation.

t = X − W − (1.715 — 1.765 mm (0.686 — 0.706 in))

X: Depth of taper roller bearing insertion part of extension case

W: Height between transfer case and taper roller bearing (transfer case side) on transfer driven gear

9. Select the adjusting washer with the nearest value in the following table.

10. Install the selected adjusting washer, dish plate and taper roller bearing (extension case side) outer race.

NOTE:

Make sure the dish plate is installed in the proper direction.

11. Measure the depth “S” between the transfer case + ST and the center differential.

12. Measure the height “T” between the extension case + ST and the transfer drive gear.

13. Calculate the adjusting washer thickness “U” using the following calculation.

U = S + T − 30 mm (1.18 in) − (0.15 — 0.35 mm (0.0059 — 0.0138 in))

S: Depth between the transfer case + ST and the center differential

T: Height between the extension case + ST and the transfer drive gear

30 mm (1.18 in): Thickness of ST (? 2 pieces)

0.15 — 0.35 mm (0.0059 — 0.0138 in): Clearance

14. Select a suitable adjusting washer in the following table.

Clearance:

0.15 — 0.35 mm (0.0059 — 0.0138 in)

15. Install the adjusting washer to center differential.

16. Apply an appropriate amount of liquid gasket.

Liquid gasket:

THREE BOND 1215B or equivalent

17. Install the extension case assembly.

Tightening torque:

40 N·m (4.1 kgf-m, 29.5 ft-lb)

18. Install the shifter arm.

NOTE:

Apply transmission gear oil to the oil seal lips.

19. Attach the gasket.

NOTE:

Use a new gasket.

20. Hang the shifter arm on 3rd-4th fork rod.

21. Install the transfer case together with the extension case assembly.

Tightening torque:

24.5 N·m (2.5 kgf-m, 18.1 ft-lb)

22. Install the back-up light switch and the neutral position switch. Switches and Harness > INSTALLATION">

23. Install the manual transmission assembly to the vehicle. Manual Transmission Assembly > INSTALLATION">

Disassembly

Transfer drive gear

Other materials:

List
EyeSight (DIAGNOSTICS) > ACC Cancel Code(s) DisplayLIST• List of ACC cancel code(s)ACC cancel codeItemContents of diagnosis02ACC Mode:Maintaining Standstill PositionDisplayed when the cruise control is cancelled after the own vehicle stops following the preceding vehicle.04ACC Mode:Stereo C ...

Installing a booster seat
WARNING Child restraint systems and seatbelts can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check the child restraint system before you place a child in it. Do not leave an unsecured child restraint system in your vehicle. ...

General diagnostic table Inspection
KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > General Diagnostic TableINSPECTION1. IMMOBILIZER SYSTEMSymptomsNoteEngine does not start Diagnostics with Phenomenon > INSPECTION"> Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2784 ANTENNA CIRCUIT (PUSH ...