Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Installation

FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Fuel Tank

INSTALLATION

1. Support the fuel tank with a transmission jack, set the fuel tank in place, and temporarily tighten the bolts of the fuel tank band.

WARNING:

A helper is required to perform this work.

2. Tighten the bolts of the fuel tank band in the order shown in the figure.

Tightening torque:

33 N·m (3.4 kgf-m, 24.3 ft-lb)

3. Install the stay - rear frame COMPL.

Tightening torque:

33 N·m (3.4 kgf-m, 24.3 ft-lb)

4. Install the heat shield cover and stopper.

Tightening torque:

18 N·m (1.8 kgf-m, 13.3 ft-lb)

5. Install the fuel tank protector. Fuel Tank Protector > INSTALLATION">

6. Connect the vent tube to the canister.

CAUTION:

Check that there is no damage or dust on the quick connector. If necessary, clean the seal surface of the pipe.

Make sure that the quick connector is securely connected.

NOTE:

Connect the quick connector as shown in the figure.

7. Securely insert the fuel filler hose (A) and evaporation hose (B) until the hose end contacts the spool, then attach the clamp or clip as shown in the figure.

Tightening torque:

2.5 N·m (0.3 kgf-m, 1.8 ft-lb)

(a)

Hose

(c)

Spool or bump

(d)

Pipe

(b)

Clamp or clip

8. Install the rear differential. Rear Differential (T-type) > INSTALLATION"> Rear Differential (VA-type) > INSTALLATION">

9. Install the rear exhaust pipe and muffler. Rear Exhaust Pipe > INSTALLATION"> Muffler > INSTALLATION">

10. Connect the quick connector of the fuel delivery tube.

CAUTION:

Check that there is no damage or dust on the quick connector. If necessary, clean the seal surface of the pipe.

When connecting the quick connector, make sure to insert it all the way in before locking the slider.

When it is difficult to lock the slider, check that the connector is fully inserted.

After locking the slider, check again that the quick connector is securely connected.

NOTE:

Connect the quick connector as shown in the figure.

(a)

Slider

11. Connect the connector to the fuel sub level sensor.

12. Install the service hole cover of fuel sub level sensor.

13. Connect the connector to the fuel pump.

14. Install the service hole cover of fuel pump.

15. Install the rear seat cushion. Rear Seat > INSTALLATION">

16. Connect the battery ground terminal.

Removal
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Fuel TankREMOVALWARNING:Place “NO OPEN FLAMES” signs near the working area.CAUTION:• Be careful not to spill fuel.• Catch the fuel from ...

Fuel tank protector
...

Other materials:

Power door locking switches
Lock Unlock All doors and the rear gate can be locked and unlocked by the power door locking switches located at the driver's side and the front passenger's side doors. To lock the doors, push the front side of the switch. To unlock the doors, push the rear side of the switch. ...

Installation
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Reverse Check SleeveINSTALLATION1. Install the reverse check sleeve.Tightening torque:6.4 N·m (0.7 kgf-m, 4.7 ft-lb)2. Install the reverse check ball, reverse accent spring, gasket and plug.NOTE:Use a new gasket.Tightening torque:9.75 N·m ...

Engine
SPECIFICATIONS > CrosstrekENGINEModel2.0 L DOHC non-turboEngine typeHorizontally opposed, liquid cooled, 4-cylinder, 4-stroke gasoline engineValve arrangementDOHCBore ? strokemm (in)84.0 ? 90.0 (3.31 ? 3.54)Displacementcm3 (cu in)1,995 (121.7)Compression ratio10.5Ignition order1 — 3 — 2 — 4 ...

© 2016-2024 Copyright www.sucross.com