Subaru Crosstrek Service Manual: Installation

1. WATER PIPE ASSEMBLY RH

1. Set the water pipe assembly RH on the engine, and connect the water pipe hose RH (B) to the oil pan upper.

2. Secure the water pipe assembly RH to the cylinder head RH with bolt (A).

Tightening torque:

6.4 N·m (0.7 kgf-m, 4.7 ft-lb)

3. Install the bolt (B) which secures the water pipe assembly RH to the cam carrier RH.

Tightening torque:

6.4 N·m (0.7 kgf-m, 4.7 ft-lb)

4. Connect the water hose (A) to the water pipe assembly RH.

5. Install the front exhaust pipe. Front Exhaust Pipe > INSTALLATION">

6. Connect the battery ground terminal. NOTE">

7. Fill engine coolant. Engine Coolant > REPLACEMENT">

1. Set the water pipe assembly LH on the engine, and connect the water pipe hose LH (B) to the oil pan upper.

2. Secure the water pipe assembly LH to the cylinder head LH with bolt (A).

Tightening torque:

6.4 N·m (0.7 kgf-m, 4.7 ft-lb)

3. Lower the engine and remove the lifting device and wire ropes.

4. Remove the bolt and turn the transmission harness counterclockwise to install the transmission harness to the control valve body. (CVT model)

Tightening torque:

7 N·m (0.7 kgf-m, 5.2 ft-lb)

5. Install the bolt which holds the transmission harness stay. (CVT model)

Tightening torque:

7 N·m (0.7 kgf-m, 5.2 ft-lb)

6. Install the transmission case cover. (CVT model)

Tightening torque:

8 N·m (0.8 kgf-m, 5.9 ft-lb)

7. Install the pitching stopper.

Tightening torque:

T1: 50 N·m (5.1 kgf-m, 36.9 ft-lb)

T2: 58 N·m (5.9 kgf-m, 42.8 ft-lb)

8. Connect the transmission radio ground terminal (C) to the vehicle body, and connect the bulkhead harness connector to the transmission harness connector (A) and the inhibitor harness connector (B). (CVT model)

Tightening torque:

13 N·m (1.3 kgf-m, 9.6 ft-lb)

9. Lift up the vehicle.

10. Install the nuts which hold the engine mounting to the front crossmember. (CVT model)

NOTE:

• Make sure that locators (A) of the engine mounting are securely inserted.

• Use a new nut.

Tightening torque:

60 N·m (6.1 kgf-m, 44.3 ft-lb)

11. Install the nuts which hold the engine mounting to the front crossmember. (MT model)

NOTE:

Use a new nut.

Tightening torque:

60 N·m (6.1 kgf-m, 44.3 ft-lb)

12. Install the front exhaust pipe. Front Exhaust Pipe > REMOVAL">

13. Lower the vehicle.

14. Secure the air breather hose to the engine rear hanger using clip. (MT model)

15. Install the bolt which secures the water pipe assembly LH to the cylinder head LH.

Tightening torque:

6.4 N·m (0.7 kgf-m, 4.7 ft-lb)

16. Connect the preheater hose (A) and the heater outlet hose (B) to the water pipe assembly LH.

17. Install the air intake case (rear).

18. Install the clip (A) which secures the air flow and intake air temperature sensor harness, and connect the connector to the air flow and intake air temperature sensor.

19. Install the air intake boot. Air Intake Boot > INSTALLATION">

20. Install the air intake duct. Air Intake Duct > INSTALLATION">

21. Install the V-belt cover.

Tightening torque:

7 N·m (0.7 kgf-m, 5.2 ft-lb)

22. Connect the battery ground terminal. NOTE">

23. Fill engine coolant. Engine Coolant > REPLACEMENT">

24. Change the front hood stay position from (B) to (A).

25. Install the front hood striker to the front hood by aligning the alignment marks (A), and close the front hood.

Tightening torque:

33 N·m (3.4 kgf-m, 24.3 ft-lb)

Removal

Water pump

Other materials:

Removal
BRAKE > Stop Light SwitchREMOVALCAUTION:Before handling the airbag system components, always refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">1. Disconnect the ground cable from battery and wait for at l ...

Dtc b2789 id code box communication
KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2789 ID CODE BOX COMMUNICATIONDTC detecting condition:• When communication between keyless access CM and ID code box is interrupted for a set amount of time.• Open ...

Inspection
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Reverse Check SleeveINSPECTION• Make sure the cutout of the reverse accent shaft is aligned with the opening in the reverse check sleeve.• Turn the cam by hand to check for smooth rotation.• Move the cam and shaft all the way toward th ...