Subaru Crosstrek Service Manual: Installation

1. Select a washer. Forward Clutch Assembly > ADJUSTMENT">

2. Install the selected washer to the reverse brake housing.

3. Install the thrust bearing to the reverse brake housing.

NOTE:

Face the temper color surface to the reverse brake side.

4. Remove the internal gear from the forward clutch assembly, and install it to the reverse brake housing.

5. Install the O-rings.

NOTE:

• Install a new O-ring.

• Apply CVTF to the O-rings.

6. Install the reverse brake assembly and internal gear as a unit to the drive pinion retainer.

NOTE:

Slowly rotate the input shaft by hand to engage the internal gear and pinion gear of planetary carrier.

Tightening torque:

37 N·m (3.8 kgf-m, 27.3 ft-lb)

7. Install the O-ring to the lubrication pipe.

NOTE:

• Install a new O-ring.

• Apply CVTF to the O-rings.

8. Install the lubrication pipe and oil guide.

Tightening torque:

16 N·m (1.6 kgf-m, 11.8 ft-lb)

9. Install the manual valve assembly and separator plate.

Tightening torque:

9 N·m (0.9 kgf-m, 6.6 ft-lb)

10. Install the primary pulley, secondary pulley and variator chain. Primary Pulley and Secondary Pulley > INSTALLATION">

11. Select shims for pulley alignment. Primary Pulley and Secondary Pulley > ADJUSTMENT">

12. Install the reduction drive gear. Reduction Drive Gear > INSTALLATION">

13. Install the transmission case. Transmission Case > INSTALLATION">

14. Install the transmission control device. Transmission Control Device > INSTALLATION">

15. Install the oil strainer and oil pan. Oil Pan and Strainer > INSTALLATION">

16. Install the reduction driven gear assembly. Reduction Driven Gear > INSTALLATION">

17. Install the transfer driven gear assembly. Transfer Driven Gear > INSTALLATION">

18. Install the transfer clutch assembly. Transfer Clutch > INSTALLATION">

19. Install the parking pawl. Parking Pawl > INSTALLATION">

20. Install the extension case. Extension Case > INSTALLATION">

21. Install the inhibitor switch. Inhibitor Switch > INSTALLATION">

22. Install the secondary speed sensor. Secondary Speed Sensor > INSTALLATION">

23. Install the primary speed sensor. Primary Speed Sensor > INSTALLATION">

24. Install the turbine speed sensor. Turbine Speed Sensor > INSTALLATION">

25. Install the transmission harness. Transmission Harness > INSTALLATION">

26. Install the control valve body. Control Valve Body > INSTALLATION">

27. Install the air breather hose. Air Breather Hose > INSTALLATION">

28. Install the transmission assembly to the vehicle. Automatic Transmission Assembly > INSTALLATION">

Inspection

Secondary pressure sensor

Other materials:

Dtc b1828 short in side airbag lh (to +b)
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B1828 SHORT IN SIDE AIRBAG LH (TO +B)Diagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting condition:• Side airbag harness (LH) is shorted to power supply.• Side airbag module (LH) is faulty.• ...

Time lag test Inspection
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Time Lag TestINSPECTIONNOTE:When the select lever is shifted while the engine is idling, there will be a certain time elapse or lag before shock is felt. This symptom helps to check the condition of forward clutch and reverse brake.• Perform the t ...

Odometer
Type A Trip knob Type B Trip knob (U.S.-spec. models) Trip knob (except U.S.-spec. models) This meter displays the odometer when the ignition switch is in the "ON" position. The odometer shows the total distance that the vehicle has been driven. If you press the trip knob ...