Subaru Crosstrek Service Manual: Installation
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Primary Pulley and Secondary Pulley
INSTALLATION
1. Select shims for pulley alignment. Primary Pulley and Secondary Pulley > ADJUSTMENT">
2. Install the seal ring to the input shaft.
NOTE:
• Use new seal rings.
• When installing the seal rings, do not expand the seal rings too much.
• Apply CVTF to the seal rings.
3. Install the seal ring to drive pinion retainer.
NOTE:
• Use new seal rings.
• Apply CVTF to the seal rings.
4. Install the selected shims to the primary pulley bearing catch surface.
5. Install the secondary pulley to the drive pinion retainer.
6. Install and tighten the secondary pulley securing bolts.
(1) Tighten the three bolts until the seating surfaces contact the bearing retainer.
NOTE:
• Be careful not to tilt the bearing retainer of the secondary pulley.
• Apply CVTF to the bolt.
(A) | Secondary pulley |
(B) | Bearing retainer |
(2) Tighten the bolts in the order of (A) > (B) > (C) > (B).
Tightening torque:
67.5 N·m (6.9 kgf-m, 49.8 ft-lb)
7. Place the variator chain on the V groove of the secondary pulley, and set the ST.
| ST 18769AA010 | EXPANDER PULLEY |
8. Expand the V groove of the secondary pulley.
9. Install the primary pulley to the reverse brake housing together with the variator chain.
CAUTION:
Cover the V grooves of primary pulley and secondary pulley with cloth to protect the both pulleys and variator chain from scratching.
(1) Intersect the V groove of primary pulley and the V groove of secondary pulley and install the secondary pulley while placing the variator chain on secondary pulley.
(2) Install the primary pulley to the reverse brake housing so that the bolt hole of primary bearing retainer and the bolt hole of reverse brake housing are aligned.
10. Install the primary pulley bolt.
Tightening torque:
21 N·m (2.1 kgf-m, 15.5 ft-lb)
11. Install the chain guide.
(1) Place the support rod inside of the variator chain.
CAUTION:
Protect the both pulleys and variator chain from scratching.
(2) Install the chain guide to the variator chain.
(3) Move the chain guide to the support rod side.
(4) While holding the support rod, press the chain guide so that the support rod runs through between the protrusions of chain guide and install the chain guide to the support rod.
(5) Install the support rod.
Tightening torque:
21 N·m (2.1 kgf-m, 15.5 ft-lb)
(6) Install the lubrication pipe.
Tightening torque:
21 N·m (2.1 kgf-m, 15.5 ft-lb)
(7) Install the chain guide so that the lubrication pipe runs through between the protrusions of each chain guide. Then remove the ST (PULLEY EXPANDER).
12. Install the reduction drive gear. Reduction Drive Gear > INSTALLATION">
13. Select the reduction drive gear shim. Reduction Drive Gear > ADJUSTMENT">
14. Install the transmission case. Transmission Case > INSTALLATION">
15. Install the transmission control device. Transmission Control Device > INSTALLATION">
16. Install the oil strainer and oil pan. Oil Pan and Strainer > INSTALLATION">
17. Install the reduction driven gear assembly. Reduction Driven Gear > INSTALLATION">
18. Install the transfer driven gear assembly. Transfer Driven Gear > INSTALLATION">
19. Install the transfer clutch assembly. Transfer Clutch > INSTALLATION">
20. Install the parking pawl. Parking Pawl > INSTALLATION">
21. Install the extension case. Extension Case > INSTALLATION">
22. Install the inhibitor switch. Inhibitor Switch > INSTALLATION">
23. Install the secondary speed sensor. Secondary Speed Sensor > INSTALLATION">
24. Install the primary speed sensor. Primary Speed Sensor > INSTALLATION">
25. Install the turbine speed sensor. Turbine Speed Sensor > INSTALLATION">
26. Install the transmission harness. Transmission Harness > INSTALLATION">
27. Install the control valve body. Control Valve Body > INSTALLATION">
28. Install the air breather hose. Air Breather Hose > INSTALLATION">
29. Install the transmission assembly to the vehicle. Automatic Transmission Assembly > INSTALLATION">
Inspection
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Primary Pulley and Secondary PulleyINSPECTION• Check the surface of primary and secondary pulley cones for damage or wear.• Check the primary ...
Other materials:
Dtc c0051 valve relay
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C0051 VALVE RELAYDTC detecting condition:Defective valve relayTrouble symptom:• ABS does not operate.• EBD does not operate.• VDC does not operate.• EyeSight does not ...
Map lights
Type A
Type B
To turn on the map light, push the switch.
To turn it off, push the switch again.
NOTE
For the type A map lights, although the
light switches are in the ON position,
the lights are automatically turned off
after approximately 30 seconds of
illumination to prevent the veh ...
Removal
SECURITY AND LOCKS > Keyless Access Indoor AntennaREMOVAL1. FRONT ANTENNA1. Disconnect the ground cable from battery. NOTE">2. Remove the cover - shift lever. Console Box > REMOVAL">3. Disconnect the connector and remove the front antenna assembly - interior.2. REAR ANTENNA1. ...
