Subaru Crosstrek Service Manual: Inspection

Subaru Crosstrek Service Manual / Security and locks / Push button start system / Inspection

SECURITY AND LOCKS > Push Button Start System

INSPECTION

1. POWER SUPPLY SWITCH FUNCTION INSPECTION

1. Check push button ignition switch function

(1) Check the change control through push button ignition switch, brake pedal operation, and shift position.

Shift lever position	Brake pedal operation	Push button ignition switch operation
P	Released	Repeat Ignition switch OFF > ACC ON > Ignition switch ON > Ignition switch OFF
P	Released	Engine running > Ignition switch OFF
P	Depressed	Ignition switch OFF > Engine started
P	Depressed	ACC ON > Engine started
P	Depressed	Ignition switch ON > Engine started
P	Depressed	Engine running > Ignition switch OFF
N	Released	Repeat Ignition switch OFF > ACC ON > Ignition switch ON > ACC ON
N	Released	Engine running > ACC ON
N	Depressed	Ignition switch OFF > Engine started
N	Depressed	ACC ON > Engine started
N	Depressed	Ignition switch ON > Engine started
N	Depressed	Engine running > ACC ON
Other than P or N	Released	Repeat Ignition switch OFF > ACC ON > Ignition switch ON > ACC ON
Other than P or N	Released	Engine running > ACC ON
Other than P or N	Depressed	Ignition switch OFF > Ignition switch ON
Other than P or N	Depressed	ACC ON > Ignition switch ON
Other than P or N	Depressed	Engine running > ACC ON

(2) Check the changeover functions other than push button ignition switch operation.

With ACC ON or the ignition switch ON, and the shift lever in “P” position, check that ACC is ON or Ignition switch is ON > Ignition switch is OFF when the vehicle is left for 1 hour or more.

(3) If the inspection result indicates an improper operation, check the push button start system. General Diagnostic Table > INSPECTION">

2. Check power status display

(1) Check the power indicator display of the push button ignition switch.

NOTE:

*1: Key collation is normal, and the stop light switch is ON.

Indicator display

Push button ignition switch status	Indicator lighting status
Ignition OFF (except for condition *1)	Light OFF
ACC ON (except for condition *1)	Orange light
Ignition ON (except for condition *1)	Orange light
Engine start standby (*1)	Green light
After engine is started	Light OFF

(2) If the inspection result indicates an improper operation, check the push button start system. General Diagnostic Table > INSPECTION">

NOTE:

The indicator blinks if any of the following malfunctions are detected.

Detected malfunction	Indicator lighting status
Steering lock stuck	Green blinking
Steering lock CM internal malfunction	Orange blinking
Keyless access CM internal malfunction	Orange blinking
Vehicle speed signal malfunction	Orange blinking

Wiring diagram

SECURITY AND LOCKS > Push Button Start SystemWIRING DIAGRAMFor wiring diagrams related to the push button start system (ignition change), refer to the following items.• Keyless access system: ...

Rear door latch and door lock actuator assembly

...

Other materials:

Dtc c1242 rear left abs sensor signal
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C1242 REAR LEFT ABS SENSOR SIGNALDTC detecting condition:• Defective ABS wheel speed sensor signal (noise, irregular signal, etc.)• Defective harness connectorTrouble symptom:&bul ...

Keyless access system check Operation
KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Keyless Access System CheckOPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».3. On «Main Menu» display, select «Each System».4. ...

Installation
DRIVE SHAFT SYSTEM > Propeller ShaftINSTALLATION1. Before installation, check the following items, and replace the propeller shaft assembly as necessary.• Dents or cracks on the tube surface• Splines for deformation or abnormal wear• Unsmooth joint operation or abnormal noise&bu ...