Subaru Crosstrek Service Manual: Inspection
SEATS > Seat Heater System
INSPECTION
1. WIRING DIAGRAM
Refer to “Seat Heater System” in the wiring diagram. Seat Heater System > WIRING DIAGRAM">
2. DIAGNOSTIC CHART
Symptoms | Repair order |
Seat heater does not operate. | 1. Check the fuse. Seat Heater System > INSPECTION"> |
2. Check the seat heater relay. Seat Heater System > INSPECTION"> | |
3. Check the seat heater system power supply and ground circuit. Seat Heater System > INSPECTION"> | |
4. Check the seat heater module. Seat Heater System > INSPECTION"> | |
5. Check the seat heater switch circuit. Seat Heater System > INSPECTION"> |
3. CHECK SEAT HEATER FUSE
Remove the seat heater fuse and inspect visually.
Is the fuse blown out?
• Yes > Replace the fuse.
• No > Check the power supply and ground circuits.
4. CHECK SEAT HEATER RELAY
1. Remove the seat heater relay from the relay holder.
2. Measure the resistance between seat heater relay terminals.
Preparation tool: Circuit tester
Terminal No. | Inspection conditions | Standard | Circuit |
36 — 37 | Always | 1 M? or more |
36 — 37
Apply battery voltage between terminals 38 — 39.
Less than 1 ?
3. Replace the seat heater relay if the inspection result is not within the standard.
5. CHECK POWER SUPPLY AND GROUND CIRCUIT
1. Check power supply circuit
(1) Disconnect the harness connector of seat heater switch.
(2) Turn the ignition switch to ON.
(3) Measure the voltage between harness connector terminal and chassis ground.
Connector & terminal
(R43) No. 7 (+) — Chassis ground (−):
Is the voltage 12 V or more?
• Yes > Go to step 2.
• No > Check the harness between the seat heater switch and fuse.
2. Check ground circuit
Measure the resistance between harness connector terminal and chassis ground.
Connector & terminal
(R43) No. 2 — Chassis ground:
Is the resistance less than 10 ??
• Yes > Go to step 3.
• No > Repair the harness.
3. Check ground circuit
Measure the resistance between seat heater switch terminals.
Connector & terminal
(R43) No. 7 — (R43) No. 2:
Is the resistance less than 10 ??
• Yes > The power supply and ground circuits are normal.
• No > Replace the seat heater switch.
6. SEAT HEATER UNIT
1. Disconnect the seat heater unit connector, and check the continuity between terminals of connector.
Connector & terminal
HI
No. 1 — No. 3:
No. 3 — No. 4:
LOW
No. 1 — No. 4:
2. If no continuity exists, replace the seat heater module with a new part.
7. SEAT HEATER SWITCH
1. Inspect the continuity between the seat heater switch terminals.
Connector & terminal
HI
No. 7 — No. 2:
No. 7 — No. 4:
No. 7 — No. 8:
LOW
No. 7 — No. 1:
No. 7 — No. 2:
No. 7 — No. 3:
2. If no continuity exists, replace the seat heater switch with a new part.
Removal
SEATS > Seat Heater SystemREMOVAL1. SEAT HEATER UNIT1. Remove the front seats. Front Seat > REMOVAL">2. Remove the backrest cover of front seat and seat cushion cover. Front Seat > ...
Other materials:
Roof rail
Roof rail
Crossbar
Cargo can be carried on the roof after
securing the crossbars to the roof rails and
installing an appropriate carrying attachment.
When installing crossbars and a
carrying attachment, follow the manufacturer's
instructions. The roof rail system is
designed to car ...
Dtc c1731 g sensor abnormal
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C1731 G SENSOR ABNORMALNOTE:For the diagnostic procedure, refer to “DTC C1732 LATERAL G SENSOR”. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G ...
Dtc u0422 invalid data received from body control module
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULENOTE:Refer to “LAN SYSTEM (DIAGNOSTICS)” for diagnostic procedures. Basic Diagnostic Procedure">1. OUTLINE OF DIAG ...
