MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Shifter Fork and Rod
INSPECTION
1. Check the shifter fork and fork rod for damage. Replace if it is damaged.
2. Gearshift mechanism
Repair or replace the gearshift mechanism if excessively worn, bent or defective in any way.
3. Inspect the clearance between 1st, 2nd driven gear and reverse driven gear. If any clearance is not within specifications, replace the shifter fork as required.
Clearance (a) and (b):
9.5 mm (0.374 in)
(A) | 1st driven gear |
(B) | Reverse driven gear |
(C) | 2nd driven gear |
1st-2nd shifter fork | ||
Part No. | Mark | Remarks |
32804AA060 | 1 | Approaches 1st gear by 0.2 mm (0.008 in). |
32804AA070 | No mark | Standard |
32804AA080 | 3 | Approaches 2nd gear by 0.2 mm (0.008 in). |
4. Inspect the clearance between the 3rd, 4th drive gear and the coupling sleeve. If any clearance is not within specifications, replace the shifter fork as required.
Clearance (a) and (b):
9.3 mm (0.366 in)
(A) | 3rd drive gear |
(B) | Coupling sleeve |
(C) | 4th drive gear |
3rd-4th shifter fork | ||
Part No. | Mark | Remarks |
32810AA061 | 1 | Approaches 4th gear by 0.2 mm (0.008 in). |
32810AA071 | No mark | Standard |
32810AA101 | 3 | Approaches 3rd gear by 0.2 mm (0.008 in). |
5. Inspect the clearance between 5th drive gear and coupling sleeve. If any clearance is not within specifications, replace the shifter fork as required.
Clearance (a):
9.3 mm (0.366 in)
(A) | 5th drive gear |
(B) | Coupling sleeve |
5th shifter fork | ||
Part No. | Mark | Remarks |
32812AA201 | 7 | Approaches 5th gear by 0.2 mm (0.008 in). |
32812AA211 | No mark | Standard |
32812AA221 | 9 | Moves away from 5th gear by 0.2 mm (0.008 in). |
6. Inspect the rod end clearances (A) and (B). If any clearance is not within specifications, replace the fork rod or shifter fork as required.
Clearance (A):
3rd-4th — 5th
0.5 — 1.3 mm (0.020 — 0.051 in)
Clearance (B):
1st-2nd — 3rd-4th
0.4 — 1.4 mm (0.016 — 0.055 in)
Dtc p0352 ignition coil "b" primary control circuit/open
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0352 IGNITION COIL "B" PRIMARY CONTROL CIRCUIT/OPENNOTE:For the diagnostic procedure, refer to DTC P0351. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0351 IGNITION COIL " ...
Installation
AIRBAG SYSTEM > Front Door Impact SensorINSTALLATIONCAUTION:Do not reuse the bolt and nut.Always replace with the specified new bolts and nuts.1. Before installation, inspect the following items and replace any faulty part with a new part.• The front door impact sensor or connector is damag ...
Id code box Note
SECURITY AND LOCKS > ID Code BoxNOTENOTE:• Equipped on C5 model with keyless access with push button start.• The ID code box is located at the place of security control module.Refer to “Security Control Module” for operation procedures on ID code box. Security Control Mod ...