Subaru Crosstrek Service Manual: Inspection

1. AUTO HEADLIGHT SYSTEM CHECK

1.CHECK HEADLIGHT ILLUMINATION.

Set the lighting switch to the switch 1 (TAIL/PARKING) and switch 2 (HEAD).

Do the tail and headlight illuminate?

Headlight System > INSPECTION">Go to Step 2.

Check the combination switch (light) and headlight bulb.

2.CHECK CURRENT DATA.

Using the Subaru Select Monitor, display the data of «Lighting AUTO input».

NOTE:

For detailed operation procedures, refer to “Application help”.

Does the display switch between OFF ←> ON when the lighting switch is moved to AUTO position?

Headlight System > INSPECTION">Go to Step 3.

Headlight System > INSPECTION">Go to Step 8.

3.CHECK CURRENT DATA.

1) Using the Subaru Select Monitor, display the data of «Illumination Sensor Output».

2) Measure the voltage when the area around the light control sensor, which was dark, becomes bright.

Illumination sensor output

Dark condition: Approx. 0.6 V or less

Bright condition: Approx. 3.0 V or more

Is the voltage output according to the brightness?

Check and replace the body integrated unit.

• Inspection: Basic Diagnostic Procedure">

• Replacement: Body Integrated Unit">

Headlight System > INSPECTION">Go to Step 4.

4.CHECK HARNESS.

1) Disconnect the connectors from body integrated unit and light control sensor.

2) Check the harness between body integrated unit and light control sensor.

Connector & terminal

(B280) No. 19 — (i226) No. 2:

(B280) No. 29 — (i226) No. 1:

(B281) No. 1 — (i226) No. 3:

Is harness normal?

Headlight System > INSPECTION">Go to Step 5.

Repair or replace the harness.

5.CHECK HARNESS.

1) Connect the connector of body integrated unit.

2) Turn the ignition switch to ON.

3) Measure the voltage between light control sensor connector and chassis ground.

Connector & terminal

(i226) No. 3 (+) — Chassis ground (−):

Is the voltage 4.5 — 5.5 V?

Headlight System > INSPECTION">Go to Step 6.

Replace the body integrated unit. Body Integrated Unit">

6.CHECK BODY INTEGRATED UNIT.

Measure the resistance between the body integrated unit and chassis ground.

Connector & terminal

(B280) No. 29 — Chassis ground:

Is the resistance less than 10 ??

Headlight System > INSPECTION">Go to Step 7.

Replace the body integrated unit. Body Integrated Unit">

7.CHECK LIGHT CONTROL SENSOR.

1) Connect the light control sensor connector.

2) Check the light control sensor. Light Control Sensor > INSPECTION">

Is the light control sensor normal?

Headlight System > INSPECTION">Go to Step 8.

Replace the light control sensor.

8.CHECK COMBINATION SWITCH (LIGHT).

Check the combination switch (light). Combination Switch (Light) > INSPECTION">

Is the combination switch (light) normal?

Headlight System > INSPECTION">Go to Step 9.

Replace the combination switch (light).

9.CHECK HARNESS.

1) Disconnect the connectors of body integrated unit and combination switch (light).

2) Check the harness between body integrated unit and combination switch (light).

Connector & terminal

(B71) No. 19 — (B281) No. 16:

Is harness normal?

Check and replace the body integrated unit.

• Inspection: Basic Diagnostic Procedure">

• Replacement: Body Integrated Unit">

Repair or replace the harness.

1.CHECK BODY INTEGRATED UNIT SETTING.

Display the data of «Welcome Light Off Delay Time(Approaching)» or «Welcome Light Off Delay Time(Exiting)» using the Subaru Select Monitor.

NOTE:

For detailed operation procedures, refer to “Application help”.

Is the setting ON?

Headlight System > INSPECTION">Go to Step 2.

Turn the setting to ON.

2.CHECK BODY INTEGRATED UNIT SETTING.

Display the data of «Illumination Sensor Setting» using Subaru Select Monitor.

Is the setting “ON”?

Headlight System > INSPECTION">Go to Step 3.

Turn the setting to “ON”.

3.CHECK AUTO HEADLIGHT.

1) Set the lighting switch to AUTO position.

2) Make the light control sensor vicinity dark.

3) Turn the ignition switch to ON.

Do the parking light, tail and headlight illuminate?

Headlight System > INSPECTION">Go to Step 4.

Check the auto headlight system. Headlight System > INSPECTION">

4.CHECK DOOR LOCK.

Operate the door lock using the keyless transmitter or the access key.

Do the lock and unlock operate properly?

Headlight System > INSPECTION">Go to Step 5.

• Check keyless entry system. Keyless Entry System > INSPECTION">

• Check the keyless access with push button start system. Basic Diagnostic Procedure">

5.CHECK BODY INTEGRATED UNIT.

1) Display the data of «IG power supply voltage» using Subaru Select Monitor.

2) Turn the ignition switch to ON.

Is the voltage 10 — 15 V?

Replace the body integrated unit. Body Integrated Unit">

Repair or replace the harness.

1.CHECK BODY INTEGRATED UNIT SETTING.

Display the data of «Welcome Light Off Delay Time(Approaching)» or «Welcome Light Off Delay Time(Exiting)» using the Subaru Select Monitor.

NOTE:

For detailed operation procedures, refer to “Application help”.

Is the illumination time setting correct?

Headlight System > INSPECTION">Go to Step 2.

Set the illumination time.

2.CHECK THE LIGHTS.

Set the lighting switch to the switch 1 (TAIL/PARKING) and switch 2 (HEAD).

Do the parking light, tail light and headlight illuminate?

Headlight System > INSPECTION">Go to Step 3.

Check the combination switch (light) and each light circuit.

3.CHECK BODY INTEGRATED UNIT.

Using the Subaru Select Monitor, display the data of «Driver’s door SW input».

Does the display switch between OFF ←> ON when driver’s door is opened/closed?

Headlight System > INSPECTION">Go to Step 4.

Check the door switch. Keyless Entry System > INSPECTION">

4.CHECK DOOR LOCK.

Operate the door lock using the keyless transmitter or the access key.

Do the lock and unlock operate properly?

Replace the body integrated unit. Body Integrated Unit">

• Check keyless entry system. Keyless Entry System > INSPECTION">

• Check the keyless access with push button start system. Basic Diagnostic Procedure">

Headlight system

Wiring diagram

Other materials:

Adjustment
AIRBAG SYSTEM > Roll ConnectorADJUSTMENTCAUTION:• Do not rotate the roll connector to more than the specified number of turns. Otherwise, the roll connector internal wire may be broken.• When determining the end stop, rotate the connector slowly without applying excessive force. Apply ...

Inspection
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Control PanelINSPECTION1. CHECK ILLUMINATION1. Check the illumination operation when battery voltage is applied between the terminals of control panel.• Manual A/C modelTerminal No.Inspection conditionsSpecificationConnection diagram14 (+) — 12 ( ...

Rear window wiper blade assembly
1. Raise the wiper arm off the rear window. 2. Turn the wiper blade assembly counterclockwise. 3. Pull the wiper blade assembly toward you to remove it from the wiper arm. 4. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 5. Hold the wiper arm ...