Subaru Crosstrek Service Manual: Inspection

Subaru Crosstrek Service Manual / Hvac system (heater, ventilator and a/c) / In-vehicle sensor (auto a/c model) / Inspection

HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > In-Vehicle Sensor (Auto A/C Model)

INSPECTION

1. Set the vehicle to the following conditions.

Item	Condition
Ignition switch	ON
A/C switch	ON
Temperature adjustment dial	HI (MAX HOT)
Air flow control dial or switch	DEF
Fan dial	HI (MAX)

2. Check the suction port (A) for in-vehicle sensor of the cover assembly - instrument panel LWR driver INN.

(1) Put a strip of paper close to the front side of the suction port (A).

(2) Can you see the paper moving towards the port and the air being sucked into the port?

CAUTION:

Be careful not to let the paper get sucked into the port.

• Yes > Go to step 5).

• No > Go to step 3).

3. Remove the cover assembly - instrument panel LWR driver INN, and check the aspirator hose (A).

(1) Are the aspirator hoses on both sides of the case and sensor connected securely?

(2) Is the aspirator hose free from any kinks or cracks?

• Yes > Go to step 4).

• No > Repair or replace the aspirator hose if necessary.

4. Check if there is anything that affects sensing, around the in-vehicle sensor.

(1) Is the in-vehicle sensor hole free from clogging?

(2) Is the peripheral area of in-vehicle sensor free from any heat-producing parts (such as audio, navigation system etc.)?

• Yes > Go to step 5).

• No > Remove everything that affects sensing.

5. Perform the inspection of in-vehicle sensor unit.

(1) Disconnect the in-vehicle sensor connector.

(2) Is the resistance between terminals of in-vehicle sensor within standard value?

CAUTION:

During inspection, be careful not to touch the sensor end in order to avoid misjudgment due to body temperature.

Preparation tool:

Circuit tester

Terminal No.	Inspection conditions	Standard
1 — 2	10°C	3.772 — 4.101 k?
	15°C	3.096 — 3.338 k?
	20°C	2.556 — 2.734 k?
	25°C	2.121 — 2.251 k?
	30°C	1.756 — 1.878 k?
	35°C	1.462 — 1.574 k?
	40°C	1.223 — 1.326 k?
	45°C	1.028 — 1.122 k?
	50°C	0.868 — 0.9542 k?
	55°C	0.7363 — 0.8147 k?
	60°C	0.6273 — 0.6984 k?

• Yes > The in-vehicle sensor is normal.

• No > Replace the in-vehicle sensor.

In-vehicle sensor (auto a/c model)

...

Removal

HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > In-Vehicle Sensor (Auto A/C Model)REMOVALCAUTION:Be careful not to damage the sensors and interior trims when removing.1. Disconnect the battery ground ca ...

Other materials:

Preparation tool
BODY CONTROL SYSTEM (DIAGNOSTICS) > General DescriptionPREPARATION TOOL1. SPECIAL TOOLILLUSTRATIONTOOL NUMBERDESCRIPTIONREMARKS — SUBARU SELECT MONITOR 4Used for setting of each function and troubleshooting for electrical system.NOTE:For detailed operation procedures of Subaru Select Monitor 4, ...

Component
REAR SUSPENSION > General DescriptionCOMPONENT1. REAR SUSPENSION(1)Rear sub frame ASSY(11)Stopper LWRTightening torque: N·m (kgf-m, ft-lb)(2)Stopper UPR(12)Flange nutT1:30 (3.06, 22.1)(3)Stay - rear frame COMPL(13)Rear stabilizerT2:33 (3.36, 24.3)(4)Front sub frame support(14)Bushing - sta ...

Installation
MECHANICAL(H4DO) > Crank SprocketINSTALLATION1. Install the crank sprocket.NOTE:The direction of installation is not specified for the crank sprocket.2. Install the timing chain. Timing Chain Assembly > INSTALLATION">3. Install the chain cover. Chain Cover > INSTALLATION"> ...