Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Inspection

FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Tumble Generator Valve Assembly

INSPECTION

1. CHECK MOTOR

1. Connect the battery positive terminal to terminal No. 5 and the battery ground terminal to terminal No. 4, and check that the valve is fully opened on LH side and the valve is fully closed on RH side.

CAUTION:

Do not power the motor for more than 10 seconds.

(A)

Full open

(B)

Full closed

2. Connect the battery positive terminal to terminal No. 4 and the battery ground terminal to terminal No. 5, and check that the valve is fully closed on LH side and the valve is fully opened on RH side.

CAUTION:

Do not power the motor for more than 10 seconds.

(A)

Full open

(B)

Full closed

2. CHECK SENSORS

1. Connect dry-cell battery positive terminal to terminal No. 3 and dry-cell battery ground terminal to terminal No. 2, and connect the resistance (0.5 — 2 k?) between dry-cell battery positive terminal and terminal No. 1.

NOTE:

Use new dry-cell batteries.

Using circuit tester, check the voltage of a single dry-cell battery is 1.6 V or more. And also check the voltage of three batteries in series is between 4.8 V and 5.2 V.

For power supply, 5 V DC voltage source can also be used.

2. Connect the circuit tester positive terminal to terminal No. 1, and the circuit tester negative terminal to terminal No. 2.

3. Connect the battery positive terminal to terminal No. 5 and the battery ground terminal to terminal No. 4, and measure the voltages with the valve fully opened on LH side and with the valve fully closed on RH side.

CAUTION:

Do not power the motor for more than 10 seconds.

(A)

Full open

(B)

Full closed

Terminal No.

Standard

1 (+) and 2 (−)

LH side: Approx. 5 V (when 25°C (77°F)) RH side: Approx. 0 — 0.5 V (when 25°C (77°F))

4. Connect dry-cell battery positive terminal to terminal No. 3 and dry-cell battery ground terminal to terminal No. 2, and connect the resistance (0.5 — 2 k?) between dry-cell battery positive terminal and terminal No. 1.

NOTE:

Use new dry-cell batteries.

Using circuit tester, check the voltage of a single dry-cell battery is 1.6 V or more. And also check the voltage of three batteries in series is between 4.8 V and 5.2 V.

For power supply, 5 V DC voltage source can also be used.

5. Connect the circuit tester positive terminal to terminal No. 1, and the circuit tester negative terminal to terminal No. 2.

6. Connect the battery positive terminal to terminal No. 4 and the battery ground terminal to terminal No. 5, and measure the voltages with the valve fully closed on LH side and with the valve fully opened on RH side.

CAUTION:

Do not power the motor for more than 10 seconds.

(A)

Full open

(B)

Full closed

Terminal No.

Standard

1 (+) and 2 (−)

LH side: Approx. 0 — 0.5 V (when 25°C (77°F)) RH side: Approx. 5 V (when 25°C (77°F))

3. OTHER INSPECTIONS

1. Check that the tumble generator valve assembly has no deformation, cracks or other damages.

2. Check tumble generator valve assembly for contamination or clogging.

Tumble generator valve assembly
...

Removal
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Tumble Generator Valve AssemblyREMOVAL1. Release the fuel pressure. Fuel > PROCEDURE">2. Disconnect the ground cable from battery.3. Remove the int ...

Other materials:

Double trip meter
Type A Trip knob Type B Trip knob (U.S.-spec. models) Trip knob (except U.S.-spec. models) This meter displays the two trip meters when the ignition switch is in the "ON" position. The trip meter shows the distance that the vehicle has been driven since you last set it to ...

Clear memory mode Operation
AIRBAG SYSTEM (DIAGNOSTICS) > Clear Memory ModeOPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».3. On «Main Menu» display, select «Each System».4. On «Select System» display, select «Ai ...

Removal
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Transmission Mounting SystemREMOVAL1. PITCHING STOPPER1. Disconnect the ground cable from battery.2. Remove the clip (A) from the air intake boot.3. Loosen the clamp (B) connecting the air intake boot and air cleaner case (rear).4. Loosen the clamp (C) ...

© 2016-2024 Copyright www.sucross.com