EyeSight (DIAGNOSTICS) > Subaru Select Monitor
INSPECTION
1. COMMUNICATION FOR INITIALIZING IMPOSSIBLE
• Communication error with stereo camera
DETECTING CONDITION:
• Defective harness connector
• Power supply circuit malfunction
• Defective stereo camera
• Defective CAN system
• Defective Subaru Select Monitor
TROUBLE SYMPTOM:
• EyeSight warning light blinks.
WIRING DIAGRAM:
EyeSight System EyeSight System > WIRING DIAGRAM">
STEP | CHECK | YES | NO |
1.CHECK IGNITION SWITCH.
Is the ignition switch ON?
Subaru Select Monitor > INSPECTION">Go to Step 2.
Turn the ignition switch to ON, and select «EyeSight» using the Subaru Select Monitor.
2.CHECK BATTERY.
1) Turn the ignition switch to OFF.
2) Measure the battery voltage.
Is the voltage 10 V or more?
Subaru Select Monitor > INSPECTION">Go to Step 3.
Charge or replace the battery.
3.CHECK BATTERY TERMINAL.
Is the battery terminal contact proper?
Subaru Select Monitor > INSPECTION">Go to Step 4.
Connect the battery terminal securely or replace it.
4.CHECK SUBARU SELECT MONITOR COMMUNICATION.
1) Turn the ignition switch to ON.
2) Using the Subaru Select Monitor, check whether the communication can be executed normally.
Is the communication between Subaru Select Monitor and body integrated unit normal?
Subaru Select Monitor > INSPECTION">Go to Step 5.
Check the connection of the Subaru Select Monitor, and perform communication with the body integrated unit again.
5.READ DTC OF BODY INTEGRATED UNIT.
Select «Body Control», and check DTC.
Is any DTC other than “Lost Communication With EyeSight” detected?
Perform the diagnosis according to DTC.
Subaru Select Monitor > INSPECTION">Go to Step 6.
6.CHECK HARNESS CONNECTOR BETWEEN STEREO CAMERA AND DATA LINK CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the stereo camera connector.
3) Measure the resistance between the stereo camera and the data link connector.
Connector & terminal
(R137) No. 10 — (B40) No. 6:
(R137) No. 9 — (B40) No. 14:
Is the resistance less than 10 ??
Subaru Select Monitor > INSPECTION">Go to Step 7.
Repair or replace the harness and connectors between the stereo camera and data link connector.
7.CHECK POWER SUPPLY CIRCUIT.
1) Turn the ignition switch to ON.
2) Measure the voltage between stereo camera and chassis ground.
Connector & terminal
(R137) No. 6 (+) — Chassis ground (−):
(R137) No. 8 (+) — Chassis ground (−):
Is the voltage 10 V or more?
Subaru Select Monitor > INSPECTION">Go to Step 8.
Repair or replace the harness and connectors between the stereo camera and fuse.
8.CHECK GROUND CIRCUIT.
1) Turn the ignition switch to OFF, then disconnect the ground cable from battery.
2) Measure the resistance between harness connector of stereo camera and chassis ground.
Connector & terminal
(R137) No. 7 — Chassis ground:
Is the resistance less than 10 ??
Subaru Select Monitor > INSPECTION">Go to Step 9.
Check the harness from stereo camera to chassis ground.
9.CHECK CONNECTOR.
Is there poor contact of stereo camera connector?
Repair the connector, or replace harness.
Replace the stereo camera. Stereo Camera > REMOVAL">
Assembly
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Transfer Case and Extension Case AssemblyASSEMBLY1. EXTENSION CASE1. Using the ST, install the oil seal to the extension case. Oil Seal">NOTE:Use a new oil seal.2. Install the dust cover.3. Install the shift bracket.Tightening torque:24.5 N&mid ...
Vehicle capacity weight
Vehicle placard
The load capacity of your vehicle is
determined by weight, not by available
cargo space. The maximum load you can
carry in your vehicle is shown on the
vehicle placard attached to the driver's
side door pillar. It includes the total weight
of the driver and all passeng ...
Pressure switch (triple pressure switch) Inspection
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Pressure Switch (Triple Pressure Switch)INSPECTION1. Connect the manifold gauge to the service valve on the high-pressure side.2. Disconnect the connector.3. Start the air conditioner, and check the operating pressure of switch by turning the compressor ...