ENTERTAINMENT > Switches and Harness
INSPECTION
1. SATELLITE SWITCH ASSEMBLY
1. Measure the resistance between connector terminals.
Preparation tool:
Circuit tester
Terminal No. | Inspection conditions | Standard | |
6 — 2 | VOL (+) VOL (−) SEEK (›) SEEK (‹) LIST RETURN | A circuit is all OFF. | Approx. 100 k? |
VOL (+) | ON | Less than 1 ? | |
VOL (−) | ON | Approx. 50 ? | |
Preset CH UP/SEEK (›) | ON | Approx. 120 ? | |
Preset CH DOWN/SEEK (‹) | ON | Approx. 230 ? | |
LIST | ON | Approx. 430 ? | |
RETURN | ON | Approx. 1,000 ? | |
12 — 2 | MUTE/ENTER TALK SOURCE ON HOOK OFF HOOK | B circuit is all OFF. | Approx. 100 k? |
MUTE/ENTER | ON | Less than 1 ? | |
TALK | ON | Approx. 50 ? | |
SOURCE | ON | Approx. 120 ? | |
ON HOOK | ON | Approx. 230 ? | |
OFF HOOK | ON | Approx. 430 ? |
2. Apply battery voltage between the connector terminals to check lighting condition of illumination inside the switch.
Terminal No. | Inspection conditions | Specification |
10 (+) — 11 (−) | Apply battery voltage. | Light ON |
3. If the result of the measurement is not at the standard, replace the satellite switch assembly.
2. TELEMATICS BUTTON
1. Check the button.
(1) Measure the resistance between connector terminals.
Preparation tool:
Circuit tester
• SOS button
Terminal No. | Inspection conditions | Standard |
6 — 1 | OFF | Approx. 1.6 k? |
ON | Less than 1 ? |
• i-button
Terminal No. | Inspection conditions | Standard |
3 — 1 | OFF | Approx. 1.6 k? |
ON | Less than 1 ? |
(2) Apply battery voltage between the connector terminals to check lighting condition of illumination inside the switch.
Terminal No. | Inspection conditions | Specification |
8 (+) — 2 (−) | Apply battery voltage. | Light ON |
2. Check the indicator.
(1) Check the continuity between the connectors.
Terminal No. | Indicator | Specification |
4 — 1 | Green | Continuity exists |
7 — 1 | Red | Continuity exists |
3. Replace the spot map light or stereo camera cover assembly if the inspection result is not within the standard value.
Sliding moonroof
Open
Close
To open:
Press and hold the rear side of the
"OPEN/CLOSE" switch. The sun shade
will also be opened together with the
moonroof. The moonroof will stop at a
position approximately 1.6 in (4 cm) away
from the fully opened position. Press and
hold the rear side of the swit ...
Dtc p2128 throttle/pedal position sensor/switch "e" circuit high
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2128 THROTTLE/PEDAL POSITION SENSOR/SWITCH "E" CIRCUIT HIGHDTC detecting condition:Immediately at fault recognitionTrouble symptom:• Improper idling• Poor driving performanceCAUTION:Afte ...
Adjustment
EXTERIOR BODY PANELS > Rear DoorADJUSTMENTAdjust the clearance around the panel assembly - rear door as follows.PartStandardAFront door sash to Rear door sash5.5+1.5, −1.0 mm (0.22+0.06, −0.04 in)BPanel assembly - front door to Panel assembly - rear door4.5±1.0 mm (0.18±0.04 in)CRoo ...